[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 141-150

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 141

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

ITD is configured as shown on a Cisco Nexus 7000 switch. Why is p.ng to VIP address still

not working?

  1. To ping VIP, you must add a probe to the device group.

  2. VIP must be from the same subnet as the ingress interface.

  3. Fail action is set to the wrong mode.

  4. This behavior is normal.

Answer: A

Question No: 142

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which command would produce this output?

  1. show stats probe type

  2. show stats HTTP

  3. show stats load balance

  4. show parameter map Answer: C

Question No: 143

Which three limitations or requirements do MP-BGP-based EVPN addresses have

compared to the initial IETF VXLAN standard (RFC 7348)? (Choose three.)

  1. Network flooding through protocol-based host MAC/IP route distribution and ARP suppression on the local VTEPs

  2. active-passive multihoming at Layer2

  3. requirement to disable multicast for underlay forwarding

  4. scalability limitations due to data-driven flood-and-learn behavior

  5. control-plane learning of end-host Layer 2 and Layer 3 reachability information, which provides integrated bridging and routing in VXLAN overla networks.

Answer: A,D,E

Question No: 144

Which option is the advantage of Cisco ACE SSL Offload?

  1. Export cipher suite

  2. Decentralized certificate management

  3. SSL encryption only

  4. Front-end SSL

Answer: D Explanation:

Ref: SSL Guide vA5(1.0)

Question No: 145

Which two options are advantages of deploying Ethernet-based FCoE switches such as the Cisco Nexus 7000 Series Switches beyond the access layer? (Choose two)

  1. lower overall throughput compared to native Fibre Channel switches

  2. flexibility to support file (NAS) and block (iSCSI and FCoE) storage traffic

  3. High-performance Ethernet-based FCoE switches cannot be used in a dedicated SAN core.

  4. requirement for traffic isolation with dedicated links and storage VDCs is no longer required.

  5. plans that include 40 and 100 Gigabit Ethernet speeds

Answer: B,E Explanation:

The other options right off are not advantages lower over throughput not and advantage, cannot be used in a dedicated SAN Core, and storage VDCs are required.

Ref:Cisco Nexus 7000 Series Switches:Ethernet Storage Directors Ref: Storage VDC On Cisco Nexus 7000 Series Switches

Question No: 146

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements about this configuration command sequence with regards to the Cisco Nexus 5500 are true. (Choose two.)

  1. It configures this node to use 0EFC2A as the first 3 bytes of the FPMA.

  2. It configures this node to use 0EFC2A as the last 3 bytes of the FPMA.

  3. It configures this node to use FCID 0EFC2A to forward the FDISC to when an endpoint is connected.

  4. It reserves this FCID so only this node can use this FCID when communicating with other Fiber Channel entities.

  5. It permits this node to form FCoE ISLs only with other nodes configured for the same FC-MAP

Answer: A,C

Question No: 147

While doing service insertion with vASA with route peering, which two parts must be configured? (Choose two.)

  1. The path for interfaces must be specified when the L4-L7 device is created.

  2. The route peering profile must be specified when the L4-L7 Service Graph template is created.

  3. The VM name must be specified when the L4-L7 device is created.

  4. The chassis must be specified when the L4-L7 device is created.

Answer: A,B

Question No: 148

Which 2 span configurations on Nexus 1K are valid?

  1. switch# configure terminal switch(config)# monitor session # ?

    switch(config-monitor)# source interface ethernet 2/1-3 switch(config-monitor)# vlan 3, 6-8 tx

    switch(config-monitor)# filter vlan 3-5,7 switch(config-monitor)# destination interface eth 2/5

  2. switch# configure terminal switch(config)# monitor session # ?

    switch(config-monitor)# source interface ethernet 2/1-3 switch(config-monitor)# vlan 3, 6-8 tx

    switch(config-monitor)# filter vlan 3-5,7 switch(config-monitor)# destination interface eth 3/5

  3. switch# configure terminal switch(config)# monitor session # ?

    switch(config-monitor)# source interface ethernet 3/1-3 switch(config-monitor)# vlan 3, 6-8 tx

    switch(config-monitor)# filter vlan 3-5,7 switch(config-monitor)# destination interface eth 2/5

  4. switch# configure terminal switch(config)# monitor session # ?

    switch(config-monitor)# source interface ethernet 3/1 switch(config-monitor)# vlan 3, 6-8 tx

    switch(config-monitor)# filter vlan 3-5,7 switch(config-monitor)# destination interface eth 3/2

  5. switch# configure terminal switch(config)# monitor session # ?

switch(config-monitor)# source interface ethernet 2/1-4 switch(config-monitor)# vlan 3, 6-8 tx

switch(config-monitor)# filter vlan 3-5,7 switch(config-monitor)# destination interface eth 2/2

Answer: A,C

Question No: 149

Which Cisco UCS Director feature provides API information and API code generation capacities that make it easy to see and work with all the available APIs, including the REST APIs and the Java APIs?

  1. report metadata

  2. REST API Browser

  3. automation feature set

  4. orchestration feature set

Answer: B

Question No: 150

In a FabricPath network, known unicast traffic is sent with the outer destination address populated with the destination SID, SSID, and local ID. Which statement describes the outer destination address in the case of unknown unicast?

  1. The outer destination address is a reserved multicast MAC address known as MC1 (010F.FFC2.02C0).

  2. The outer destination address is a broadcast address (FFFF.FFFF.FFFF).

  3. The outer destination address is not required because FabricPath uses the FTag to forward unknown unicast.

  4. The outer destination address is a reserved multicast MAC address known as MC1 (010F.FFC1.01C0).

Answer: D

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 131-140

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 131

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which statement about these commands is true?

  1. The outputs of the debug are redirected on file test on the quot;log.quot; directory.

  2. The outputs of the debug are redirected to the logging buffer.

  3. The command does not have an effect unless you configure quot;debug enablequot;.

  4. If you are on a console connection, the outputs are shown after the event occurs.

Answer: A Explanation: Ref:

http://www.cisco.com/web/techdoc/dc/reference/cli/nxos/commands/fund/debug_logfile.htm l

Question No: 132

Which three options are key characteristics of the data center core layer in a three-tier architecture? (Choose three.)

  1. Provides scalability

  2. Used to enforce network security

  3. Performs Qos marking

  4. Provides connectivity to distribution layer

  5. Performs policing

  6. High availability

Answer: A,D,F Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/DC_Infra2_5/D CInfra_1.html

Question No: 133

FabricPath brings the benefits of routing protocols to Layer 2 network Ethernet environments. Which thee options describe advantages of using FabricPath technology? (Choose three.)

  1. MAC address scalability with conversational learning

  2. loop mitigation with TTL in the frame field

  3. Spanning Tree Protocol independence

  4. 10-Gb/s bandwidth

  5. Layer 2 extensions between data centers

Answer: A,B,C

Question No: 134

Which two statements about OpenStack are true? (Choose 2)

  1. Horizon is the component that is used for IP address management.

  2. Nova is the compute component that is used to manage and automate the provisioning of compute

    resources.

  3. Keystone is the networking component that is used to create and manage network resources.

  4. Neutron is the networking component that is used to create and manage network resources.

  5. Trove is the GUI web application that is used to control and configure different 0penStack components.

Answer: D,E

Question No: 135

Which three options are common PTP device types? (Choose three.)

  1. ordinary clock

  2. network clock

  3. crystal clock

  4. transparent clock

  5. boundary clock

  6. sundials

Answer: A,D,E

Question No: 136

Refer to the exhibit. The switch is running Fabricpath, however the CE port e1/9 is not on spanning tree forwarding. Which option describes the possible cause?

Dumps4Cert 2017 PDF and VCE

  1. Switch 1 is receiving better BPDU on E1/9.

  2. Bridge assurance is configured on switch 1 E1/9 but not configured on the facing interface.

  3. Switch 1 is not configured with FabricPath.

  4. Loopguard feature is blocking the port.

Answer: A

Question No: 137

Which two actions are used by the OT\/join interface on an edge device? (Choose 2)

  1. Join the overlay network and discover the other remote OT\/ edge devices.

  2. Form OTV adjacencies with the other OTV edge devices that belong to the same VPN

  3. Send/receive only multicast traffic.

  4. Forward Layer 2 frame destined for a remote site an overlay interface.

  5. Only receive MAC reachability information.

Answer: A,B

Question No: 138 DRAG DROP

Drag and drop the term of the Cisco Prime Service Catalog from the left column onto the

correct definition on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Initiator Delivery Plan

Service manager Performer Customer

Question No: 139

Which three benefits do VXLANs offer compared to VLANs? (Choose three.)

  1. VXIAN uses a 16-bit VNID to overcome the 4094 VLAN scale limitation.

  2. It provides better utilization of available network paths in the overlay infrastructure.

  3. VXLAN uses a 24-bit VNID to overcome the 4094 VLAN scale limitation.

  4. It provides better utilization of available network paths in the underlay infrastructure.

  5. It provides a solution to extend Layer 2 segments over a single Layer 2 VLAN.

  6. It provides a solution to extend Layer 2 segments over a shared Layer 3 routed network.

Answer: C,D,F

Question No: 140

Which three options can be used to add a device as a member to a zone? (Choose 3)

  1. Fibre Channel ID

  2. IP address

  3. LUN ID

  4. fully qualified domain name

  5. device alias

  6. VLAN ID

Answer: A,C,E

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 121-130

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 121

Which three statements about the virtual service domain on Cisco Nexus 1000v Switch are true? (Choose Three)

  1. Service virtual machine only snoops the data and is used for monitoring purpose.

  2. Any traffic coming into the VSD or going out of the VSD must go through the service virtual machine.

  3. A virtual service domain (VSD) allows you to classify and separate traffic for network service.

  4. vMotion is supported for the service virtual machine and should not be disabled.

  5. A VSD is the collection of interfaces that are guarded by the service virtual machine.

  6. The show virtualservice-domainname command displays the configuration for this VSD port profile.

Answer: B,C,E

Question No: 122

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which outcome of this configuration is true?

  1. It enables call home policies to take effect.

  2. Fabric interconnects can view neighbor switches.

  3. It enables the CIM XML service.

  4. It displays Cisco UCS Central on the UCSM portal page.

Answer: B

Question No: 123

Refer to the exhibit.

***Exhibit is Missing***

How many virtual adapters (vN|C and vHBA) can be added to this host?

A. 130

B. 128

C. 256

D. 258

Answer: C

Question No: 124

Which two statements about OTV are true?(Choose two)

  1. The authoritative edge device is the active forwarder for multicast and unknown unicast for all VLANs.

  2. The join interface must be a Layer 2 interface.

  3. no special license is required for OTV.

  4. OTV requires a separate VDC if SVIs for the extended VLANs are to be configured on the same switch.

  5. Only one join interface can be specified per overlay.

  6. OTV runs over a distance victor routing protocol. Answer: D,E

Question No: 125

You want to make 80 Gbps of bandwidth available to your RedHat servers. Which two

statements are true? (Choose two.)

  1. Install 2208 lOMs, VIC 1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  2. Install 2204 lOMs, VIC1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  3. Install 2204 lOMs, V1C1240 CNAs, and create four vNICs mapped to each fabric.

  4. Install 2204 IOMs, VIC 1280 CNAs, and create four vNICs mapped to each fabric.

  5. Install 2204 lOMs, VIC 1240 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  6. Install 2208 IOMs, VIC 1280 CNAs, fabric extenders, and create eight vNICs mapped to each fabric.

Answer: C,F

Question No: 126

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

When specifying subnets under a bridge domain for given tenant, the user can specify the scope of a subnet. Which definition of the public subnet scope is true?

  1. It indicates that this subnet is advertised to the external router by the border leaf.

  2. It indicates that this subnet is advertised to public Internet and must be protected by a firewall.

  3. It indicates that it must be leaked to one or more private networks within ACI fabric.

  4. It indicates that this subnet is advertised to the border leaf in ACI fabric

Answer: A

Question No: 127

Which three options are valid sources for Cisco UCS monitor sessions? (Choose 3)

  1. VHBA

  2. uplink FC interface

  3. VLAN

  4. vNIC

  5. VSAN

  6. pin group

Answer: A,B,E

Question No: 128

Which descripting of how to enable the Flex Flash Controller auto-sync function on the B200M4 blade is true?

  1. Configure a focal disk policy for FlexFlash.

  2. Enable auto-sync in the servers gt; inventory gt; storage subtab.

  3. Configure a storage policy for FX3S.

  4. Configure a storage connection policy to use auto-sync.

Answer: B

Question No: 129

On Cisco Nexus 1000v Switch, you can allow the VSM and VEM to communicate over IP for control and packet traffic.Before you create a port profile for Layer 3 control, which two statements must be verified? (Choose two)

  1. Only one port profile can be configured with the capability Layer 3 control command.

  2. All VEMs belong to the same Layer 2 domain.

  3. The transport mode for the VSM domain should be configured as Layer 3.

  4. The port profile must be a trunk port profile.

  5. Different hosts should belong to the same VLANs for Layer 3 control. Answer: A,C

Question No: 130

Which option is the minimum number of vNICS required by the service profile to connect to all available

Vlans

  1. 6

  2. 7

  3. 3

  4. 1

Answer: C

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 111-120

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 111

Which two guidelines apply to private VLAN configuration when you are running FabricPath? (Choose two.)

  1. On the F-Series modules, user-configured static MAC addresses are programmed on all forwarding engines that have ports in that VLAN.

  2. All VLANs in a private VLAN must be in the same VLAN mode; either CE or FabricPath.

  3. FabricPath ports can be put into a private VLAN

  4. The system does support hierarchical static MAC addresses

Answer: A,B

Question No: 112

Which three options are types of iSCSI node names? (Choose three)

  1. extended unique identifier

  2. iSCSI unique identifier

  3. extended qualified name

  4. network address authority

  5. iSCSI qualified name

  6. network qualified name Answer: A,D,E

Question No: 113

Refer to exhibit.

Dumps4Cert 2017 PDF and VCE

ABC Company recently implemented the network load balancing solution across distributed data centers. It does not work as expected.

Which option is possible solution to address the issue?

  1. Enable selective unknown unicast flooding.

  2. Add static ARP entry on Cisco Nexus for both load balancers.

  3. Add a new OTV broadcast group

  4. Use a dedicated VLAN for network load balancer. Answer: A

Question No: 114

Which two statements about Cisco UCS Director API access key are true? (Choose two.)

  1. API access key is a unique security access key code that is associated with a specific Cisco UCS Director user account.

  2. API access key is a shared secret that you must configure m Cisco UCS Director to enable REST API.

  3. API access key is unique for each API request.

  4. API access Key is required for Cisco UCS Director to authenticate API requests.

Answer: A,D

Question No: 115

Which two statements about IP-directed broadcast are true? (Choose two.)

  1. An IP-directed broadcast is an IP packet whose destination address is a valid broadcast address, and it originates from a node that is also part of the same subnet.

  2. A switch that is not directly connected to its destination subnet forwards an IP-directed

    broadcast in the same way it forwards unicast IP packets destined to a host on that subnet.

  3. All switches in the network forward an IP-directed broadcast in the same way they forward multicast IP packets.

  4. The destination address in the IP header of the packet is rewritten to the configured IP broadcast address for the subnet, and the packet is sent as a link-layer broadcast.

Answer: A,D

Question No: 116

Where is FIP negotiated?

  1. between E Nodes and VF ports

  2. between E Nodes and F Nodes

  3. between VF ports

  4. between VN ports

  5. between VN ports and VF ports and FCFs Answer: E

Question No: 117 DRAG DROP

Drag and drop the feature from the left onto the correct benefit on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Congestion Notification IEEE 802.1 Qau

Data center Bridging Exchange DCBX

Priority-Based Flow Control IEEE 802.1 Qbb

Enhanced transmission selection IEEE 802.1 Qaz

Question No: 118

Which three statements are considered best practice when directly connection converged network adapters to the fabric? Choose three.)

  1. If the converged access switches (in the same SAN fabric or in the other) must be connected to each over Ethernet links for the purposes of LAN alternate pathing, then such links must explicitly be configured to include all FCoE VLANs. This configuration ensures to extend the scope of the Spanning Tree Protocol for FCoE VLANs to Cisco Unified Fabric and non Cisco Unified Fabric links.

  2. Cisco UF links must be configured as spanning-tree edge ports.

  3. If MSTP is enabled, a separate MST instance must be used for FCoE VLANs.

  4. Separate FCoE VLANs must be used for FCoE in SAN-A and SAN-B.

  5. A shared VLAN can be used to carry traffic for each virtual fabric in the SAN (for example, VLAN 1002 for VSAN 1, VSAN 2, and so on).

  6. Cisco Unified Fabric links must be configured as access ports and FCoE VLAN must not be configured as a native VLAN.

Answer: B,C,D

Question No: 119

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which statement is not true?

  1. Chassis 1 in blade 2 has a major fault.

  2. Those service profiles have a user acknowledge maintenance policy configured.

  3. If you check Acknowledge All and click Apply, the blades reload.

  4. Any user can acknowledge the reload

Answer: D

Explanation: Ref: Cisco UCS Manager 2.2 Guide

Question No: 120

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Many tools are available to troubleshoot an ACI fabric. Which tool is this sample output from?

  1. iPing

  2. traffic map

  3. atomic counters

  4. traceroute

Answer: C

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 101-110

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 101

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two options are possible reasons for device being stuck in quot;initquot; mode? (Choose two.)

  1. Incorrect credentials are provided.

  2. No quot;chassisquot; is selected.

  3. Incorrect quot;Function typequot; is selected.

  4. No management interface is specified in quot;Cluster interfacesquot; section.

  5. Incorrect VM is selected.

  6. quot;http service enablequot; is not configured on the ASA.

Answer: A,F

Question No: 102

Refer to the Exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are true? (Choose two.)

  1. You can enable Multicast Optimized to as many classes as you want as long as enough unutilized multicast queues are available.

  2. Four different MTUs are allowed: 1500.2158, 2240, and 9000.

  3. If you save the policy, it gives you an error because you can have the Fibre Channel class and one more as no drop policy. To fix it, check all the check boxes under packet Drop except one.

  4. Three different MTUs are 1500, 2158, and 9000

  5. If you save the policy, it gives you an error because you can have only one class with the no drop policy. To fix it, check all the check boxes under Packet Drop because the class Fibre Channel is already a no-drop class

Answer: D,E

Question No: 103

Which three commands must be run to enable support of adapter-fex on an interface on Cisco Nexus Switch?

(Choose 3)

  1. feature adapter-fex

  2. feature-set adapter-fex

  3. feature-set virtualization

  4. feature fex

  5. switchport mode adapter-fex

  6. switchport mode vntag

Answer: A,C,F

Question No: 104

In which location can device package logs be found?

  1. /data/lt;device package namegt;/logs

  2. /data/devicescript/lt;device package namegt;/logs

  3. /data/devicescript/loga

  4. /Var/logs/dme/log/lt;device package namegt;/logs

  5. /var/sysmgr/tmp_logs/lt;device package namegt;/logs

Answer: B

Question No: 105

Which three PVLAN port modes are supported on Cisco Nexus 9000? (Choose three.)

  1. port channels

  2. isolated host trunk

  3. FEX port

  4. virtual port channels

  5. isolated host

  6. community host

Answer: B,E,F

Question No: 106

Refer to exhibit.

Dumps4Cert 2017 PDF and VCE

Which option describes what happens to a packet with an MTU of 2158 when it is switched from E1/1 to E1/2?

C:\Users\Raiy\Pictures\39.jpg

  1. It is punted to the CPU.

  2. It is dropped.

  3. It is fragmented.

  4. It is forwarded with no fragmentation. Answer: D

Question No: 107

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which statement about this command sequence when it is performed on a Cisco Nexus 5500 chassis is true?

  1. All VLANs except the FCoE VLAN are shut down on the interface.

  2. You must add the VLAN number to the shutdown command to specify which VLAN is to be shut down.

  3. There is no shutdown lan command.

  4. The interface is shut down and all traffic stops.

  5. The VLAN for FCoE traffic is shut down and FCoE traffic stops.

Answer: A Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/fcoe/6x/b_55 00_FCoE_Config_6x/b_5500_FCoE_Config_602N11_chapter_010.html

Question No: 108

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

After you upgrade Cisco UCS firmware, some of your blades have these error messages. Which description of the problem is true?

  1. Service profile requires a connectivity policy.

  2. Storage provisioning is not configured.

  3. vNIC template must be converted to updating.

  4. Some components are deprecated.

Answer: A

Question No: 109 DRAG DROP

Drag and drops the feature from the left onto the correct description on the right

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 110

Which solution is preferred for predictable traffic in a vMware environment running Cisco Nexus 1000v Series switches?

  1. end-host mode

  2. fabric failover mode

  3. client mode

  4. server mode

  5. standalone mode

Answer: A

Explanation: Ref: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-1000v- switch-vmware-vsphere/white_paper_c11-558242.html

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 91-100

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 91

Which three statements about the vTracker feature after it is enabled on the Cisco Nexus 1000v switch are true? (Choose three)

  1. The vTracker feature provides information about the virtual machines that are managed by all Cisco Nexus Switches.

  2. The vTracker feature uses the Link Layer Discovery Protocol.

  3. All vTracker views are valid for a given time only.

  4. The vTracker feature provides information about the virtual network ebvironment.

  5. The VSM and vCenter must be on same subnet.

  6. The VSM must be connected with the vCenter to collect information. Answer: C,D,F

Question No: 92

Refer to the exhibit,

Dumps4Cert 2017 PDF and VCE

which two statements about spanning tree are true? (Choose two)

  1. BPDUs from a vPC are processed on this switch

  2. BPDUs are processed and generated by both peer switches.

  3. This switch cannot generate BPDUs for a vPC.

  4. BPDUs are sent to the peer switch for processing.

  5. BPDUs received on this switch are dropped because of Type 2 inconsistency issues.

  6. This switch generates BPDUs for vPC. Answer: C,D

Question No: 93

Which cisco UCS Director features enables you to view the REST API URL for every report display in cisco UCS Director?

  1. Orchestration features set

  2. REST API Brower

  3. Automation feature set

  4. Report metadata

Answer: D

Question No: 94

Which two statements about end-host mode are true? (Choose two.)

  1. In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repms the vMIC, and the vNIC go

  2. End-host mode allows the fabric in interconnect to act as an end host to the network, representing all servers (hosts) connected to it through vNICs.

  3. End-host mode is the default Ethernet switching mode.

  4. In end-host mode, the fabric interconnect runs the 5pann,ng Tree Protocol to avoid loops.

  5. In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repins the vNIC but the vNIC remain down until manual intervention.

Answer: B,C

Explanation: Ref: http://www.cisco.com/c/en/us/solutions/collateral/data-center- virtualization/unified-computing/whitepaper_c11-701962.html

Question No: 95 DRAG DROP

Drag and drop the correct port security configuration on the left to the correct action on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Shut Down Protect Errdisable Restrict

Dumps4Cert 2017 PDF and VCE

鈥?/p>

http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifShutdown-Shuts down the interface that received the packet triggering the violation. The interface is error disabled. This action is the default. After you reenable the interface, it retains its port security configuration, including its secure MAC addresses.

You can use the errdisable global configuration command to configure the device to reenable the interface automatically if a shutdown occurs, or you can manually reenable the interface by entering the shutdown and no shut down interface configuration

commands.

Dumps4Cert 2017 PDF and VCE

鈥?/p>

Dumps4Cert 2017 PDF and VCE

http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifRestrict-Drops ingress traffic from any nonsecure MAC addresses. The device keeps a count of the number of dropped packets.

鈥?/p>

http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifProtect-Prevents violations from occurring. Address learning continues until the maximum number of MAC addresses on the interface is reached, after which the device disables learning on the interface and drops all ingress traffic from nonsecure MAC addresses.

Question No: 96

Which three port types support port security in Nexus 7000? (Choose 3)

  1. access ports.

  2. vPC ports

  3. SPAN source ports.

  4. Layer 2 and Layer 3 ports.

  5. SPAN destination ports.

  6. trunk ports.

Answer: A,C,F

Question No: 97

Which two security features are supported by IMX-API? (Choose two.)

  1. All communication the device is encrypted when you use VPN.

  2. All communication to the device is encrypted when you use HTTPS.

  3. NX-API support certificate-based authentication.

  4. Users must have appropriate accounts to access the device through NX-API.

Answer: B,D

Question No: 98

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

The administrator has been provided with this topology, but has not been provided with the IP address of storage switch and has been asked zoning. Which two CLI commands can be used to determine the management addresses of the storage switches? (Choose two)

  1. show npv status

  2. show fcns database

  3. show fcdomain status

  4. show fcdomain domain-list

  5. show fcdomain statistics

  6. show cfs internal ethernet-peer

  7. show cfs peers

  8. show npv internal info

Answer: G,H Explanation: Ref:

http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_2_x/san- os/configuration/guide/cfs.html

Ref: http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_1_x/1_0_2/san- os/configuration/guide/MgngStorDevc.html

Question No: 99

How do you manually configure a vNIC MAC address?

  1. Use the mac -address-table static command.

  2. Modify the dynamic vNIC connection policy.

  3. Use the set identity dynamic-mac command.

  4. Modify the adapter policy.

Answer: D

Question No: 100

Which three statements about direct-attached storage are true? (Choose three)

  1. The fabric interconnect must be in Fibre Channel switch mode.

  2. If you connect to Cisco NX-OS on the fabric interconnect, you can see the flogi by using the show flogi database vsan lt;vsan IDgt; Command.

  3. For maintenance of direct attached storage, you must define a maintenance policy.

  4. The fabric interconnect must be end-host mode.

  5. you need not map an FCoE VLAN when creating the storage VSAN.

  6. to configure the zoning, you must create a storage connection policy.

Answer: A,B,F Explanation:

Ref: http://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs- infrastructure-ucs-manager-software/116082-config-ucs-das-00.html

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 81-90

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 81

Refer to the exhibit.

Within an ACI fabric, a routing protocol is needed to assist with route redistribution between

the outside networks and the internal fabric. Which routing protocol is needed to run in the fabric at location 1 to allow the VM access to the networks advertised by the external Layer 3 network.

  1. eBGP

  2. OSPF

  3. MP-BGP

  4. iBGP

  5. IS-IS

Answer: C

Question No: 82 DRAG DROP

Drag and drop two configurations that should fail without data loss from the left column into the 2 Devices Lost column on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 83 DRAG DROP

Drag and drop terms at the Cisco Prime Service Catalog from the left onto the definition on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Authorization persmissions

Review Requistion Service group

Question No: 84 DRAG DROP

Drag and drop feature on the left onto the appropriate business benefits on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation:

ETS

Data Center Bridging Exchange (DCBX) Protocol Fiber Channel over Ethernet (FCoE)

PFC

Ref:Cisco White Paper Data Center Bridging

Question No: 85

You configured a new appliance port, but the port has a pinning failure. Which option is possible cause?

  1. The appliance port admin speed must be adjusted.

  2. Appliance VLANs are missing duplicate global VLANs.

  3. The appliance is configured for NPV.

  4. Appliance VLANs are duplicated in global VLANs.

Answer: D

Question No: 86

Which Ether type is used to identify FIP?

A. 0x8914 B. 0x8906 C. 0x8915 D. 0x8905

Answer: A Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/fcoe/513_n1_ 1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1

_chapter_010.html

Question No: 87

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are true? (Choose two.)

  1. Three pin groups are configured: one for the port-channel 10 in fabric interconnect B, one for int el/32 in fabric interconnect B, and one for int e1/31 in fabric interconnect B.

  2. Changing the target interface for an existing SAN pin group disrupts traffic for all vHBAs that use that pin group. The fabric interconnect performs a log in and log out for the Fibre Channel protocols to repin the traffic.

  3. To configure pinning for a server, you must include the SAN pin group in a vNIC policy. The vNIC policy is then included in the service profile assigned to that server. All traffic from the vNIC travels through the I/O module to the specified uplink Fibre channel port.

  4. In Fibre Channel switch mode, SAN pin groups are irrelevant. Any existing SAN pin groups are ignored.

  5. Edit this to show switch mode

Answer: B,D Explanation:

Ref: http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/1-0- 2/b_GUI_Config_Guide/GUI_Config_Guide_chapter19.html

Also see PDF: Configuring SAN Pin Groups

Question No: 88

Which option lists the valid roles for VSM?

  1. primary and secondary

  2. standalone, primary, and secondary

  3. central, primary, and secondary

  4. master and slave

Answer: B Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/4_0/high_ava ilibility/configuration/guide/n1000v_ha/ha_3system.html

Question No: 89

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Corporate ABC wants to implement control by allowing authorized virtual machine MAC addresses to send traffic to the Internet. The administrator wants to add this MAC ACL on Nexus7k-1 to achieve the task

[Configuration Output] Nexus7k-1:

mac access-list mac-acl

permit 0050.561f.73d3 0000.00ff.ffff any

!

interface e1/1

mac access-group mac-acl

However, this action does not work. Which two statements describe the issue? (Choose two.)

  1. The MAC address and mask do not match.

  2. The MAC ACL cannot be applied to egress traffic.

  3. This command is wrong to apply this ACL under interface.

  4. The sequence number is missing from the ACL.

  5. The MAC ACL is not supported on Cisco nexus 7000 Series.

Answer: B,C Explanation:

Ref: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx- os/security/configuration/guide/sec_nx-os-cfg/sec_macacls.html

B is definitely correct as you can only apply a MAC ACLs to ingress traffic only

You can apply a MAC ACL as a port ACL to Layer 2, Layer 3, and Port-Channels but the command is as follows:

mac access-list acl-mac-01

permit 00c0.4f00.0000 0000.00ff.ffff any interface ethernet 2/1

mac port access-group acl-mac-01

Question No: 90

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which outcome of this configuration is true?

  1. Any newly created traffic flows do not use this fabric interconnect.

  2. All traffic ceases to flow through this fabric interconnect after a reboot.

  3. Servers cease to use this fabric interconnect upon next reboot.

  4. All traffic ceases to flow through this fabric interconnect.

Answer: D

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 71-80

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 71

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

ABC company has successfully implemented the smart call home.

Which three configuration components for CallHome are mandatory? (Choose three)

  1. periodic inventory interval

  2. alert group to collect output

  3. destination profile

  4. email server and from email address

  5. contact information

  6. system contact Answer: D,E,F

Question No: 72

In which EPG is the consumer interface of an L4-L7 device placed?

  1. provider EPG

  2. shadow consumer EPG

  3. consumer EPG

  4. shadow provider EPG

Answer: B

Question No: 73

Cisco UCS Director provides an option to offer the report metadata and REST API Browser for developers. Which configuration step is needed Cisco USC Director to enable this feature?

  1. Enable the developer menu.

  2. Enable report metadata

  3. Enable the debugging menu.

  4. Enable the REST API

Answer: A

Question No: 74

Which two products provide the ability to create eight VDCs? (Choose two)

  1. Cisco Nexus 7000 Supervisor 2 Module

  2. Cisco Nexus 7000 Supervisor 1 Module

  3. Cisco Nexus 7700 Supervisor 1 Module

  4. Cisco Nexus 7700 Supervisor 2E Module

  5. Cisco Nexus 7000 Supervisor 2E Module Answer: D,E

Question No: 75

Which three configurations can be different between EVPN vPC peers? (Choose 3)

  1. using a different secondary IP address

  2. loopback primary IP address

  3. using the same primary IP addresses

  4. consistent NVE1 binding to the same loopback interface

  5. consistent VLAN to VN-segment mapping

  6. consistent VNI to group mapping

Answer: D,E,F

Question No: 76 DRAG DROP

Drag and drop the objects of the ACI policy model from left onto the correct definition on right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Bridge domain Application profile

context EPG

Contracts Tenant

Question No: 77

After VTEP devices have established BGP neighbor adjacencies with other VTEPs or with Internal BGP route reflectors, which three pieces of information are exchanged through BGP? (Choose three.)

  1. Layer 3 VNI

  2. VTEP peer list

  3. VPNv4 prefixes

  4. VTEP address

  5. router MAC address

Answer: A,D,E

Question No: 78

Which two statements about VXLAN are true? (Choose two.)

  1. VXLAN adds an additional 32 bytes worth of headers.

  2. Devices that terminate VXLAN tunnels are known as VTEPs.

  3. A VTEP is a virtual or physical device that maps end devices to VXLAN segments.

  4. VXLAN uses a UDP destination port of 4987.

Answer: B,C

Question No: 79

Considering the ITIL v3 model, what are Puppet and Chef primary used for?

  1. problem management

  2. configuration management

  3. change management

  4. release management

Answer: B

Question No: 80

Which mode must the Cisco MDS VSAN be configured for so that it interoperates correctly with a Brocade Fibre Channel switch that is configured for interop mode?

  1. interop mode 2

  2. interop mode 4

  3. interop mode 3

  4. native mode

  5. interop mode 1 Answer: E

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 61-70

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 61

Which two guidelines and limitations of NetFlow on Cisco NX-OS are true? (Choose two.)

  1. Only Layer 2 NetFlow is applied on Layer 2 interfaces, and only Layer 3 NetFlow is applied on Layer 3 interfaces.

  2. If you change a Layer 2 interface to a Layer 3 interface, the software converts the Layer 2 NetFlow to Layer 3 NetFlow automatica

  3. You must configure a source interface. If you do not configure a source interface, the exporter remains in a disabled state.

  4. The Cisco Nexus 2000 Series Fabric Extender does not support bridged NetFlow.

  5. Valid record name is optional to configure.

Answer: A,D

Question No: 62

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Your application has a reduced health score. Upon inspection, you find a fault that impacts the health score. The fault currently is in the soaking lifecycle state. Which two options are possible next steps while in this state? (Choose two.)

  1. The condition ceases by itself and automatically clears the fault.

  2. The soaking timer expires and moves to the Raised severity level.

  3. Acknowledge the fault, which immediately clears it from the system.

  4. The condition ceases by itself and goes into the soaking-clearing state.

Answer: B,D

Question No: 63

Which two actions are necessary to configure FCoE on the Cisco Nexus 7000 Switches?(choose two)

  1. The dedicated and shared interfaces are configured.

  2. The system quality of service is disabled.

  3. The module is licensed for Layer 2 and Layer 3.

  4. The Cisco Nexus 7000 has the FCoE feature enabled.

  5. The two required storage virtual contexts are created. Answer: A,D

Question No: 64

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two CLI actions are appropriate to try to resolve the enhanced zoning lock problem? (Choose two.)

  1. Use the dear zone lock command to remove the lock Use this command on each switch in the fabric for VSAN 16 only.

  2. Use the show zone internal vsan 16 command to determ.ne the IP address of the user and the MDS switch where the lock is currently held.

  3. Use the no zone commit vsan command on me switch that holds the lock to release the lock if you are the holder of the lock.

  4. Use the no zone commit vsan lt;vsan idgt; force command on the switch that holds the lock to release the lock if another user holds the lock.

  5. Using either Cisco Fabric Manager or the CLI, reactivate the existing zone set for VSAN

16. Be careful to only reactivate and not deactivate activate to avoid a disruption in service.

Answer: C,D

Question No: 65

Which three statements about the Cisco Fibre Channel Domain feature are true? (Choose three)

  1. It is responsible for domain ID distribution.

  2. It is responsible for fabric reconfiguration.

  3. The domains are configured on a switch-wide basis.

  4. It functions as described in the FC-EE standards.

  5. It acts as relay agent for the FC ID allocations that are distributed by the Fibre Channel Time Server(ff.ff.fb)

  6. It is responsible for principal switch selection. Answer: A,B,F

Question No: 66

Which two statements about basic zoning are true? (Choose two)

  1. If a zone is part of multiple zone setsyou create one instance of this zone for both zone sets.

  2. To retrieve the results of the activation on a per switch basis. The managing switch provides a combined status about the activation and identifies the failure switch.

  3. Administrators can make simultaneous configuration changes. Upon activation.one administrator can overwrite another administrator#39;s changes.

  4. The default zone policy is defined per switch. To ensure smooth fabric operation, all switches in the fabric must have the same default zone setting

  5. To distribute the zoning database, you must reactivate the same zone set. The reactivation may affect hardware changes for hard zoning only on the local switch, remote switch, remote switches are not affected.

Answer: C,D

Question No: 67

Which two Cisco Nexus 2000 Series Fabric Extenders support FCoE? (Choose two.)

  1. 2248TP

  2. 2232ET-P

  3. 2224TP

  4. 2232PP

  5. 2232TM-E

Answer: D,E Explanation:

Ref: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-2000-series-fabric- extenders/data_sheet_c78-507093.html

Question No: 68

Refer to the exhibit.

Which command on a Cisco UCS provides this output?

  1. show npv info

  2. show npv external-Interface-usage

  3. show npv status

  4. show npv traffic-map

Answer: C

Question No: 69

Which two statements about FabricPath are true? (Choose two)

  1. Multi-destination trees are built to create a loop-free topology for unicast traffic.

  2. FabricPath interfaces send and receive Ethernet and FabricPath encapsulated packets.

  3. FabricPath is supported on Cisco Nexus 7000 on all module types.

  4. FabricPath switch should always be the root for a spanning tree network attached to it.

  5. Spanning tree does not run inside a FabricPath network.

Answer: D,E

Question No: 70

Which definition of Intelligent Service Card Manager is true?

  1. part of the RISE service that is responsible for establishing initial connectivity with remote appliances (for example. Citrix NetScaler)

  2. management software to manage Cisco Nexus devices

  3. management software to manage provisioning of RISE services on a Cisco Nexus

    switch

  4. part of the RISE service that resides on a Cisco Nexus switch that is responsible for handling tasks related to receiving Route Health Injection massages from appliances and programming those routes in the universal routing information base

  5. part of the RISE service that resides on an appliance (for example, Citrix NetScaler) that is responsible for sending Route Health Injection massages to a Cisco Nexus switch

Answer: A

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 51-60

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 51

Which statement about soft pinning is incorrect?

  1. If no uplink Ethernet port channel is configured with all VLANs on the vNIC.Cisco UCS Manager drops the traffic for all of the VLANs on the vNIC.

  2. When the VLAN validation fails, a VLAN mismatch fault with a severity of warning appears.

  3. It is the default behavior Cisco UCS.

  4. Cisco UCS Manager pins the vNIC to an uplink Ethernet port or port channel according to VLAN membership criteria.

Answer: B

Question No: 52

Which two statements about the Cisco Open SDN Controller are true? (Choose 2)

  1. It can be used in multivendor environments.

  2. It is a commercial distribution based on the OpenFlow controller.

  3. The controller is available as an appliance only.

  4. Security is enforced by using the Open Services Gateway Initiative framework.

  5. Your own, new network service functions can be added via Java APls.

Answer: A,E

Question No: 53

Which three guidelines and limitations of policy-based routing are true? (Choose three.)

  1. An ACL used in a policy-based routing route map cannot include a deny statement.

  2. A policy-based routing route map can have multiple match or set statements per route- map statement.

  3. Policy-based routing and WCCPv2 are not supported on the same interface if bank chaining is disabled.

  4. The same route map can be shared among different interfaces for policy-based routing as long as the interfaces belong to the same VRF instance.

  5. Setting a tunnel interface or an IP address via a tunnel interface as a next hop in a policy-based routing policy is not supported.

  6. A match command can refer to more than one ACL in a route map used for policy-based routing.

Answer: A,D,E

Question No: 54

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Assuming no traffic engineering has been configured, what is the link speed of port channel 200?

  1. 1 Gbps

  2. 6 Gbps

  3. 4 Gbps

  4. 8 Gbps

Answer: D

Question No: 55

Which two options does ITD replace? (Choose two.)

  1. Layer 7 load balancer

  2. Access lists

  3. Policy-based routing

  4. IP SLA

  5. Layer 4 load balancer

  6. WCCP

Answer: C,F

Question No: 56

Which statement about the converged network adapter is true?

  1. The converged network adapter is a multifunction adapter that combines the functions of Ethernet NICs and Fibre Channel host bus adapters.

  2. The converged network adapters are compatible only with Cisco UCS.

  3. The converged network adapter is a virtualized multifunction adapter that combines the functions of Ethernet NICs and iSCSI on the same card.

  4. The converged network adapter is a multifunction adapter that works with multiple network speeds and duplex settings, and it supports several storage and network protocols.

Answer: A

Explanation: Ref: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000- series-switches/data_sheet_c78-618603.html

Question No: 57

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which cause of this error is true?

  1. The upstream switch is in NPV mode.

  2. VSAN mismatch on an uplink.

  3. The upstream switch port is disabled.

  4. No interfaces have been configured as uplinks.

Answer: A

Question No: 58 DRAG DROP

Drag and drop the mode of operation on left onto the correct definition on right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation:

Power supply and input source redundancy (full redundancy) Combined

Power supply redundancy (N 1)

Input source redundancy (grid redundancy)

Ref: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-7000-series- switches/Data_Sheet_C78-437761.html

Question No: 59 DRAG DROP

An admin is updating an existing Cisco UCS environment to accommodate a new storage array that will be directly attached to the Cisco UCS.

Unmanaged servers external to the Cisco UCS fabric interconnects will also access the new array existing Cisco UCS service profiles will be used to access the new storage array.

Drag and drop the appropriate steps from left into the correct order on the right to migrate the Cisco UCS to support the new storage array.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation: Configure UCS into FC Switching Mode Configure Storage Port on UCS

Configure Zoning on upstream switch Create/Configure LUN Masking on Storage Array The general process to configure DAS in UCS is:

->Configure FI in FC switch mode.

->Create required virtual SAN (VSAN).

->Set the port role in UCS.

->Check if the storage port worldwide port name (WWPN) is logged in to the fabric.

Ref: http://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs- infrastructure-ucs-manager-software/116082-config-ucs-das-00.html

Question No: 60

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

SwitchA and switchB have these zonesets currently active and are connected by an ISL that is configured to transport VSA Enhanced zoning is configured for VSAN, and merge- control is set to restrict. Which statement about this configuration is true?

  1. Enhanced zoning is configured, so the user is prompted on the CLI to permit or deny Zone2 into the active zone set.

  2. Zone merge fails because the currently active zone sets are not identical.

  3. Zone merge succeeds and the resulting zone set matches switchB.

  4. Zone merge fails because merge-control set to restrict, which means that merges are never permitted.

  5. Zone merge succeeds but Zone2 is dropped from the active zone set because it is not currently included in the active zone set in switchA.

Answer: E

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE