[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 341-350

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 341 – (Topic 3)

An IPv6 network has different MTUs on different segments, if the network is experiencing reliability issues, which option is the most likely reason?

  1. ICMPv6 is filtered.

  2. The Do Not Fragment bit is marked.

  3. HSRPv6 is configured incorrectly.

  4. The MTU size is greater than 1470 bytes.

Answer: B

Question No: 342 – (Topic 3)

Which IP SLA operation requires Cisco endpoints?

  1. UDP Jitter for VoIP

  2. ICMP Path Echo

  3. ICMP Echo

  4. UDP Jitter

Answer: A

Question No: 343 – (Topic 3)

Which congestion-avoidance or congestion-management technique can cause global synchronization?

  1. Tail drop

  2. Random early detection

  3. Weighted random early detection

  4. Weighted fair queuing

Answer: A

Question No: 344 – (Topic 3)

What are three of the key fields that define a unique NetFlow flow?(3)

  1. Layer 3 protocol type

  2. Type of service

  3. Source MAC address

  4. Canonical Format identifier

  5. Input logical interface

  6. Cyclic Redundancy Check

Answer: A,B,E

Question No: 345 – (Topic 3)

What are three valid HSRP states? (Choose three)

  1. listen

  2. learning

  3. full

  4. established

  5. speak

  6. IN IT

Answer: A,E,F

Question No: 346 – (Topic 3)

How can you reduce latency on a VoIP network?

  1. Set the IP SLA timeout to 1000 milliseconds

  2. Implement fast retransmission

  3. Configure an SLA to collect information on packet loss

  4. Implement low-latency queuing

  5. Implement a congestion-avoidance algorithm

Answer: D

Question No: 347 – (Topic 3)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit.Which configuration must you apply to a router so that it can generate a log message in the given format?

  1. service sequence-numbers

    B service timestamps log datetime

  2. service timestamps log uptime

  3. service alignment logging

Answer: C

Question No: 348 – (Topic 3)

What technology allows a PE router to exchange VPNv4 routes with other PE routers?

  1. MPLSL3VPN B MPLSL2VPN

  2. VPLS

  3. Frame Relay to ATM AAL5 Interworking

Answer: A

Question No: 349 – (Topic 3)

Which three technologies can be used to implement redundancy for IPv6? (Choose three)

  1. IPv6 NA

  2. NHRP

  3. HSRP

  4. DVMRP

  5. GLBP

  6. IPv6 RA

Answer: C,E,F

Question No: 350 – (Topic 3)

Which option describes how the IP address is assigned when you configure a Layer 3 EtherChannel interface?

  1. You must assign the IP address to the tunnel interface.

  2. The last IP address added to the EtherChannel is used automatically.

  3. You must assign the IP address to a port channel logical interface.

  4. The first IP address added to the EtherChannel is used automatically.

Answer: C

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 331-340

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 331 – (Topic 2)

What is the default behavior for a manual summary route when a component route of the summary disappears?

  1. Regardless of the metric of the component route ,the metric of the summary is unchanged in order to keep stability

  2. If the component route previously had the best composite metric, the same summary metric is retained for stability /

  3. If the component route previously had the best composite metric, the metric of the summary changes to the next-best composite metric

  4. If the component route previously dis not have the best composite metric, the summary metric is updated and updates are sent to peers

Answer: A

Question No: 332 – (Topic 2)

what is the source MAC address of a BPDU frame that is sent out of a port ?

  1. the lowest MAC address on the switch

  2. the higest MAC address on the switch

  3. the MAC address of the individual port that is sending the BPDU

  4. the same as the MAC address in the brigdge ID

Answer: C

Question No: 333 – (Topic 2)

What is the function of the command ip pim autorp listener?

  1. It allows the mapping agents to accept autorp information from the PIM rendezvous point.

  2. It allows a BSR to accept autorp information and translate it into BSR messages.

  3. It allows the routers to flood the atuorp information in a sparse-mode-only network.

  4. It allows a border PIM spare-mode router to accept autorp information from another

autonomous system.

Answer: C

Topic 3, Pool C

Question No: 334 – (Topic 3)

Which two statements about IP source guard are true?(Choose two.)

  1. It must be applied to EtherChannel port members

  2. It is available only on L2 ports.

  3. It is supported in software only.

  4. It is not supported on private VLANS.

  5. It blocks DHCP packets

Answer: B,D

Question No: 335 – (Topic 3)

Which statement about EIGRP request packets is true?

  1. They determine whether a destination is reachable

  2. They are transmitted unreliably

  3. They are transmitted via broadcast

  4. They are sent in response to queries

Answer: B

Question No: 336 DRAG DROP – (Topic 3)

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 337 – (Topic 3)

What command can you enter to enable client autoconfiguration over an ISATAP tunnel?

  1. tunnel mode ipv6ip isatap

  2. no ipv6 nd ra suppress

  3. ipv6 nd ra suppress

  4. tunnel mode ipv6ip 6rd

Answer: B

Question No: 338 – (Topic 3)

Which feature can protect against broadcast DoS attacks?

  1. storm control

  2. DHCP snooping

  3. DAI

  4. IP Source Guard

Answer: A

Question No: 339 – (Topic 3)

Which statement about Cisco StackWise technology is true?

  1. Every switch in a stack has its own independent and uncoordinated configuration file

  2. All switches in a stack share configuration and routing information to behave as a single unit

  3. Removing switches can affect stack performance

  4. Only the master switch acts as a forwarding processor

Answer: A

Question No: 340 – (Topic 3)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. If R1 contacts the RADIUS server but is unable to find the user name in the server database, how will R1 respond?

  1. It will attempt to authenticate the user against the local database

  2. It will attempt to contact the TACACS server

  3. It will prompt the user to enter a new username

  4. It will deny the user access

Answer: B

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 321-330

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 321 – (Topic 2)

Which three modes are valid for forming an EtherChannel between the ports of two switches? {Choose three)

  1. passive/passive

  2. active/active

  3. active/passive

  4. desirable/on

  5. auto/auto

  6. auto/desirable

Answer: B,C,F

Question No: 322 – (Topic 2)

Which two statements are true about 6to4 tunneling? (Choose two)

  1. It works by appending the public IPv4 address (converted into hexadecimal format) to the 2002::/16 prefix.

  2. It embeds the IPv6 packet into the IPv4 payload with the protocol type set to 51.

  3. It works by appending the private IPv4 address (converted into hexadecimal format) to the 2002::/16 prefix.

  4. It embeds the IPv6 packet into the IPv4 payload with the protocol type set to 41.

Answer: A,D

Question No: 323 – (Topic 2)

Which two EtherChannel modes can create an LACP EtherChannel?(Choose two)

  1. on

  2. active

  3. passive

  4. auto

  5. desirable

Answer: B,C

Question No: 324 – (Topic 2)

Exhibit:

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. If a console port is configured as shown, which response is displayed when you connect to the console port?

  1. the message quot;Authorized users onlyquot;

  2. the username prompt

  3. a blinking cursor.

  4. three username name prompts followed by a timeout message.

  5. the message quot;Connection refused.quot;

Answer: C

Question No: 325 – (Topic 2)

Which option is can example Qf SaaS?

  1. Google Apps

  2. Amazon AWs

  3. Google App Engine

  4. Microsoft Azure

Answer: A

Question No: 326 – (Topic 2)

Which is the maximum number of classes that MQC can support in a single policy map ?

A. 512

B. 256

C. 128

D. 64

Answer: B

Question No: 327 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements about this topology are true? (Choose two)

  1. Destination 192.168.23.0/24 is unable to use interface Fa0/1 as the LFA.

  2. Interface FastEthernet 0/1 is the primary path to destination 192.168.23.0/24.

  3. The FastEthernet 0/0 and FastEthernet 0/1 interfaces are used as LFA for destination 192.168.23.0/24

  4. Only interface FastEthernet 0/1 are used as the LFA for destination 192.168.23.0/24.

  5. Interface FastEthernet 0/0 is the primary path to destination 192.168.23.0/24.

  6. Only FastEthernet 0/0 is used as the LFA to destination 192.168.23.0/24.

Answer: A,E

Question No: 328 – (Topic 2)

Which statement about WAN Ethernet Services is true?

  1. UNIs can perform service multiplexing and all-in-one bundling

  2. Point-to-point processing and encapsulation are performed on the customer network.

  3. Ethernet multipoint service function as a multipoint-to-multipoint VLAN-based connection

  4. Rate-limiting can be configured per EVC.

Answer: D

Question No: 329 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

What type of IS-IS is configured on R1?

  1. VRF-aware IS-IS

  2. ISIS version 2

  3. single-topology IS-IS

  4. mufti-process IS-IS

Answer: C

Question No: 330 – (Topic 2)

Which two options about PIM-DM are true? (Choose two)

  1. In a PIM-DM network, routers that have no upstream neighbors prune back unwanted traffic

  2. PIM-DM initially floods multicast traffic throughout the network.

  3. PIM-DM supports only shared trees.

  4. PIM-DM uses a pull model to deliver multicast traffic.

  5. PIM-DM cannot be used to build a shared distribution tree.

Answer: B,E

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 311-320

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 311 – (Topic 2)

Exhibit:

Dumps4Cert 2017 PDF and VCE

  1. The PPP multilink protocol header is omitted on delay-sensitive packets.

  2. The maximum number of fragments is 1.

  3. Small real-time packets are multilink-encapsulated.

  4. A transmit queue is provided for smaller packets

Answer: A,D

Question No: 312 – (Topic 2)

Which command sets the maximum segment size for a TCP packet initiated from a router?

  1. ip tcp window-size

  2. ip tcp mss

  3. ip mtu

  4. ip tcp adjust-mss

Answer: B

Question No: 313 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which three statements about the R1 configuration are true? (Choose three)

  1. The virtual circuit identifier is 4006 and the virtual circuit is down.

  2. This circuit is using MPLS VC type 4.

  3. The local label for the circuit is 1611.

  4. The virtual circuit identifier is 1611 and the virtual circuit is down.

  5. The targeted LDP session to the remote peer is up.

  6. The local label for the circuit is 4006.

Answer: D,E,F

Question No: 314 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two options are effects of the given configuration? (Choose two)

  1. It enables Cisco Express Forwarding on interface FastEthernetO/0

  2. It sets the data export destination to 209.165.200.227 on UDP port 49152

  3. It enables NetFlow switching on interface FastEthernetO/0

  4. It configures the export process to include the BGP peer AS of the router gathering the data.

  5. It sets the data export destination to 209.165.200.227 on TCP port 49152.

Answer: B,C

Question No: 315 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are true? (Choose two)

  1. This router is 4-byte autonomous system aware.

  2. This router is not 4-byte autonomous system aware.

  3. The prefix 10.100.1.1/32 was learned through an autonomous system number with a length of 4 bytes, and this router is not 4-byte autonomous system aware.

  4. The prefix 10.100.1.1/32 was learned through an autonomous system number with a length of 4 bytes, and this router is 4-byte autonomous system aware.

  5. The prefix 10.100.1.1/32 was originated from a 4-byte autonomous system

Answer: B,C

Question No: 316 – (Topic 2)

Which command can you enter to disable logging for terminal lines?

  1. no logging trop

  2. no logging monitor

  3. no logging buffer

  4. no logging console

  5. no logging count

Answer: B

Question No: 317 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to exhibit. R1, R2, and R3 are in different statellite offices of the same organization. A multiast vido source is located behind R1. R3 frequently receives video streams interded for R2. These streams saturate the available bandwidth of R3. Which configuration change can alleviate the congestion on R3?

  1. Configure R3 to send an immediate-leave message when necessary 10 stop receiving unwanted traffic

  2. Configure IGMP snooping on R1 R 2 and R3

  3. Place a PIM filter 贸n the switches and interfaces that connect 10 R1R2 and R3

  4. Enable IGMP snooping On all switches that contect to R1 R2 and R3

  5. Place a PIM filter on the switch and interface that connect to R1 only

Answer: D

Question No: 318 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. Which two conclusions can you draw from this command and its output?(choose two)

  1. Rl0 has a missing label binding (or 192.168.40.171/32

  2. The MPLS ping failed

  3. 192.168.40.171/32 exists in the global routing table

  4. A valid LSP exists and it matches the corresponding MPLS FEC

  5. The MPLS ping was successful

  6. R10 has a valid lablel binding for 192.168.40.171/32

Answer: A,B

Question No: 319 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. R1 and R2 have been configured as BGP neighbors, but their session is stuck in active. Which action can you take that will enable a session to be established?

  1. Enable synchronization on R1 R2

  2. Issue the neighbor 10.1.12 .2 activate command on R#39;1

  3. Configure 10.1.12.1 as the BGP router 10 on R1

  4. Configure a neighbor relation ship with the Loopback0 address of R1 on R2

Answer: D

Question No: 320 – (Topic 2)

Which option describes show a network administrator prevents possible routing loops for VLSM subnets that are missing from the routing table?

  1. Create a route for the subnet to the null interface and then redistribute the static route into the routing process.

  2. Create a loopback interface with the correct subnet and then redistribute the connected interface to the routing table

  3. Create a loopback interface with the correct subnet and the routing protocol automatically injects it into its routing process

  4. Create a route for the subnet to the null interface and the routing protocol automatically injects it into its routing process.

Answer: A

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 301-310

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 301 – (Topic 2)

Which option descripbes a difference between Ansible and Puppet?

  1. Ansible is client-server based and Puppet is not

  2. Ansible requires an agent and Puppet does not

  3. Ansible is Python based and Puppet is Ruby based

  4. Ansible automates repetitive tasks and Puppet allow you to run plain ssh commands

Answer: C

Question No: 302 DRAG DROP – (Topic 2)

Drag and drop each IPv6 migration method from the left onto the matching description on the right. Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 303 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements about this capture true? (Choose two)

  1. It is set to run for five minutes

  2. It is set to use the default buffer type

  3. It captures data only until the buffer is full

  4. It is set to run for a period of 00:03:26

  5. It continues to captures to capture data after the buffer is full

Answer: A,E

Question No: 304 – (Topic 2)

Exhibit:

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. What is the DSCP value that egresses SW2 toward R2?

  1. 0

  2. 2

  3. 8

  4. 10

  5. 16

Answer: A

Question No: 305 – (Topic 2)

Which two statements about IS-IS are true? {Choose two)

  1. The default hello interval is 10 seconds and the default hold timer is 30 seconds.

  2. Both IS-IS routers need to have the same capabilities in the hello packet in order to form neighbors.

  3. The hello interval can be changed on a per-interface basis with the command ISIS hello- multiplier.

  4. Both routers need to have the same hello intervals and hello timers in order to form IS- IS neighbors.

Answer: A,C

Question No: 306 – (Topic 2)

You are configuring Wireshark on a Cisco Catalyst 4500E Switch a Supervisor 8. Which three action can you take to prevent the capture from overloading the CPU? {Choose three)

  1. Use an in-line filter.

  2. Reconfigure the buffers to accommodate the additional traffic.

  3. Attach the specific ports that are part of the data path.

  4. Configure a policy a policy map, class map, and an access list to express the match conditions.

  5. Use an appropriate ACL

  6. Add memory to the Supervisor.

Answer: A,C,E

Question No: 307 – (Topic 2)

An IP SLA fails to generate statistics. How can you fix the problem?

  1. Add the verify-data command to the router configuration

  2. Reload the router configuration.

  3. Remove the ip sla schedule statement from the router configuration and re-enter it.

  4. Add the debug ip sla trace command to the router configuration.

  5. Add the debug ip sla error command to the router configuration.

Answer: A

Question No: 308 – (Topic 2)

On an MPLS L3VPN, which two tasks are performed by the PE router? (Choose two.)

  1. It exchanges VPNv4 routes with other PE routers.

  2. It typically exchanges iBGP routing updates with the CE device.

  3. It distributes labels and forwards labeled packets.

  4. It exchanges VPNv4 routes with CE devices.

  5. It forwards labeled packets between CE devices.

Answer: A,C

Question No: 309 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. This routes is advertising which routes via BGP?

  1. BGP routes that originated on RT1

  2. AJI routes

  3. all BGProutes from AS 65006

  4. BGP routes that originated from AS 65006 and BGP routes that originated on this router

  5. No routes

Answer: D

Question No: 310 – (Topic 2)

Which two options are pruposes of MSDP SA filtering?(Choose two)

  1. to improve the scalability of an MSDP multicast environment

  2. to reduce the number of multicast addresses that are distributed to other devices in the

    same multicast domain

  3. to allow all SA messages to be processed by MSDP peers

  4. to reduce the number of multicast addresses that are shared to MSDP peers

  5. to allow the filtering of IGMP messages between peers

  6. to allow the filtering of PIM messages between peers

Answer: A,D

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 291-300

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 291 – (Topic 2)

Which two statement about BPDU guard are true ?

  1. BPDU guard can be used to prevent an invalid BPDU from propagating through the network.

  2. BPDU guard can be used to prevent an access port from participating in the spanning tree in the service provider environment.

  3. The global configuration command spanning-tree portfast bpduguard default shuts down interface that are in the PortFast-operational state when a BPDU is received on that port.

  4. BPDU guard can be used to protect the root port.

  5. The interface configuration command spanning-tree portfast bpduguard enable shuts down only interface with PortFast enabled when a BPDU is received.

Answer: B,C

Question No: 292 – (Topic 2)

What is the EUI 64-bit address corresponding to MAC address 0032F4C57781?

A. FFFE0032F4C57781 B. 0032F4FFFEC57781 C. 0032F4C57781FFFE D. C57781FFFE0032F4

Answer: B

Question No: 293 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which statement about the Rlmulticastcast network environment is true?

  1. . RPF builds the topology using the unicast data for source address 10.1.108.10.

  2. A static mrouteis configured to point multicast traffic for 10.30.30.32 through Ethernet 1/0.

  3. RPF uses the OSPF 100 table for source address 10.1.108.10.

  4. The default mroute uses Tunnel 10 as the next hop for 10.1.108.10.

Answer: B

Question No: 294 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

What is the effect on the network when you apply these configuration to RI and R2?

  1. Asymmetric routing occurs because the bandwidth and delay K value settings are mismatched.

  2. The interface bandwidth and delay settings adjust automatically to match the new metric settings

  3. The neighbor adjacency between R1 and R2 temporarily resets and then reestablishes itself.

  4. R1 and R2 fail to form a neighbor adjacency.

Answer: D

Question No: 295 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

The Main 1 and Branch 1 switches are connected directly over over an MPLS pseudowire, and both runn UDLD. After router B1 reloads because of a power failure, the pseudowire.

However the Branch 1 switch is unable to reach the Main 1 switch. Which two actions can you take to restore connectivity and problem from recurring? (Choose two)

  1. Configure a backup pseudowire between the Main 1 and Branch I Switchs.

  2. Issue the shutdown and no shutdown commands on the Branch 1 switch uplink to the B1 router only.

  3. Configure a backup GRE tunnel between the Main I and Branch 1 switches.

  4. Issue the shutdown and no shutdown commands on both the Branch 1 switch uplink to the B1 router and the Main 1 switch#39;s uplink to the M1 router

  5. Enable errdisable recovery on both the Main I and Branch I switches.

  6. Enable UDLD recovery on both the Main I and Branch I switches.

Answer: B,E

Question No: 296 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

What is the PHB class on this?

  1. EF

  2. CS4

  3. none

  4. AF21

Answer: B

Question No: 297 – (Topic 2)

Which two OSPF network type require the use of a DR and BDR? {Choose two)

  1. non-broadcast networks

  2. point-to-point networks

  3. point-to-point non-broadcast networks

  4. broadcast networks

  5. point-to-multipoint networks

Answer: A,D

Question No: 298 DRAG DROP – (Topic 2)

Drag each 0SPFv2 SA parameter on the left to its corresponding description on the right. Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 299 – (Topic 2)

Which statement about the RPF interface in a BIDIR-PIM network is true?

  1. In a BIDIR-PIM network the RPF interface can be the interface that is used reach the PIM rendezvous or the interface that is used to reach the source.

  2. In a BIDIR-PIM network the RPF interface is always the interface that is used to reach the source.

  3. There is no RPF interface concept in BIDIR-PIM networks

  4. In a BIDIR network the RPF interface is always the interface that is used to reach the PIM rendezvous point.

Answer: D

Question No: 300 DRAG DROP – (Topic 2)

Drag each NTP command on the left to its effect on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 281-290

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 281 – (Topic 2)

Which regular expression will match prefixes from the AS 200 that directly connected to our AS?

A. A$

B. A200)

C. _200$

D. A200_ E- _200_

Answer: D

Question No: 282 – (Topic 2)

Exhibit:

Dumps4Cert 2017 PDF and VCE

With BGP always-compare-med enabled, which BGP entry is installed in the RIB?

  1. Entry 1 because it was installed first (oldest) in the BGP table.

  2. Entry 1 because it has the best MED of the external routes.

  3. Entry 2 because it has the lowest router ID.

  4. Entry 3 because it has the lowest MED.

Answer: D

Question No: 283 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Why is the OSPF state in 2WAY/DROTHER?

  1. There is a duplicate router ID

  2. This is the expected output when R1 is the DR.

  3. There is an MTU mismatch.

  4. This is expected output when the interface EthernetO/0 of RI is configured with OSPF Priority 0.

  5. There is an OSPF timer (hello/dead) mismatch.

Answer: D

Question No: 284 – (Topic 2)

For which two conditions is Cisco Express Forwarding recursion disables by default when the BGP Prefix independent Convergence functionality is enabled? (Choose two)

  1. next hops that are directly connected

  2. next hops learned with any mask shorter than /32

  3. next hops learned with a/32 mask

  4. next hops learned with a/24 mask

Answer: A,C

Question No: 285 – (Topic 2)

In a simple MPLS L3VPN. which two tasks are performed by a PE router?(Choose two)

  1. It establishes pseudowires with other PEs

  2. It exchanges VPNv4 or VPNv6 routes with CE devices

  3. It assigns labels to routes in individual VPNs…

  4. It forwards labeled packets to CE devices

  5. It exchanges VPNv4 or VPNv6 routes with oth.er PE routers

Answer: C,E

Question No: 286 – (Topic 2)

Which three elements compose a network entity title? (Choose three.)

  1. area ID

  2. domain ID

  3. system ID

  4. NSAP selector

  5. MAC address

  6. IP address

Answer: A,C,D

Question No: 287 – (Topic 2)

Which two statements about the default SNMP configuration are true? (Choose two)

  1. All SNMP notification types are sent

  2. The SNMP trap receiver is congigured

  3. SNMPv3 is the default version

  4. The SNMP agent is enabled.

  5. SNMPv1 is the default version.

Answer: A,E

Question No: 288 – (Topic 2)

Which three options are the main security features in SNMPv3? (choose three)

  1. authentication

  2. MIB persistence

  3. message integrity

  4. authorization

  5. encryption

  6. accounting

Answer: A,C,E

Question No: 289 DRAG DROP – (Topic 2)

Drag and drop each step in the uRPF packet-forwarding process from the left into of operations on the right. Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 290 – (Topic 2)

Which statement about Auto-RP is true ?

  1. All interface s must be configured in sparse modE.

  2. All interfaces must be configured in sparse-dense mode.

  3. All interfaces must be configured in dense modE.

  4. An RP that it tied to a loopback address must be configured.

Answer: D

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 271-280

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 271 – (Topic 2)

Which three pieces of information are carried on OSPF type-3 LSAs? (Choose three)

  1. metric

  2. authentication type

  3. link state

  4. IP subnet

  5. externaI route tag

  6. subnet mask

Answer: A,D,F

Question No: 272 – (Topic 2)

Which two statements about PPP PAP are true?(Choose two)

  1. It requires two-way authentication

  2. It can protect against playback attacks

  3. It is supported only on synchronous interfaces

  4. It is vulnerable to trial-and-error attacks

  5. Login attempts are controlled by the remote node

Answer: A,E

Question No: 273 – (Topic 2)

Which two statements about the BGP community attribute are true?(Choose two.)

  1. Routers send the community attribute to all BGP neighbors automatically.

  2. A router can change a received community attribute before advertising it to peers.

  3. It is a well-known, discretionary BGP attribute.

  4. It is an optional transitive BGP attribute.

  5. A prefix can support only one community attribute.

Answer: B,D

Question No: 274 – (Topic 2)

How does MSTP maintain compatibility with RSTP?

  1. The system ID of an RSTP BPDU is padded with extra bytes to match the format of an MSTP BPDU.

  2. MSTP sends all spanning-tree information in one BPDU

  3. RSTP encodes region information from an MSTP BPDU into a single instance.

  4. MSTP supports five port states in the same way as RSTP.

  5. RSTP implements a TTL that is compatible with the MSTP max age timer.

Answer: A

Question No: 275 – (Topic 2)

Which IPv6 tunneling type establishes a permanent link between IPv6 domains over IPv4?

  1. 6to4 tunneling

  2. ISATAP tunneling

  3. IPv4-compatible tunneling

  4. manual tunneling

Answer: D

Question No: 276 – (Topic 2)

Your NetFlow collector is not working due to a large amount of traffic entering your network which is destined to a single IP address. Which NetFlow feature allows you to collect the top source hosts for this traffic on the local router?

  1. NetFlow can export flows only to.a external flow collector

  2. ip flow-top-talkers

  3. ip accounting

  4. show ip cache flow

Answer: B

Question No: 277 – (Topic 2)

Refer to the exhibit. Which network script automation option or tool is used in the exhibit?

Dumps4Cert 2017 PDF and VCE

  1. EEP

  2. Python

  3. Bash script

  4. NETCONF

  5. RESET

Answer: B

Question No: 278 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit .Which two statements about the output are true?(Choose two)

  1. BFD on RT1 has negotiated the BFD capability with its pe r

  2. BFD is active on interface GigabitEthernet0/3 and is using ICMP

  3. BFD is active on interface GigabitEthernet0/3 and is using UDP

  4. BFD last failed 476 ms ago on interface GigabitEthernet0/3 /

  5. BFD is active for BGP on RT1

Answer: D,E

Question No: 279 DRAG DROP – (Topic 2)

Drag and drop each STP po role on the le to the matching statement on the right.

Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 280 – (Topic 2)

Which two statements about IPv4 and IPv6 networks are true? ( Choose two)

  1. IPv6 uses a required checksum at the network layer

  2. In IPv4 fragmentation is permed by the source of the packet

  3. IPv4 uses an optional checksum at the transport layer

  4. IPv6 uses a UDP checksum to verify packet integrity

  5. In IPv6routers perform fragmentation

  6. In IPv6hosts perform fragmentation

Answer: D,F

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 261-270

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 261 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit . What tag will be applied to the 172.16.130.0/24 route?

  1. 10

  2. 20

  3. 30

  4. 40

Answer: B

Question No: 262 DRAG DROP – (Topic 2)

Drag and drop each multicast protocol from the left onto the matching description on the right.

Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 263 DRAG DROP – (Topic 2)

Drag and drop the OSPF network type on the left to the correct category of timers on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 264 – (Topic 2)

Which statement about a Cisco APIC controller versus a more traditional SDN controller is true?

  1. APIC uses a policy agent to translate policies into instructions

  2. APIC supports OpFlexas a Northbound protocol

  3. APIC does suppoort a Southbound REST API

  4. APIC uses an imperative model

Answer: B

Question No: 265 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Notice that debug ip bgp updates has been enables. What can you conclude from the debug output?

  1. BGP neighbor 10.1.3.4 established a new BGP session.

  2. This is result of clear ip bgp 10.1.2.3 in command.

  3. This is result of the clear ip bgp 10.1.3.4 out command.

  4. BGP neighbor 10.1.3.4 performed a graceful restart.

Answer: B

Question No: 266 – (Topic 2)

Which option is the Cisco recommended method to secure access to the console port?

  1. Set the privilege level to a value less than 15

  2. Configure a very short timeout (less than 100 milliseconds) for the port

  3. Configure the activation-character command

  4. Configure an ACL

Answer: C

Question No: 267 – (Topic 2)

Which two statements about a flat single-hub DMVPN with NHRP are true?(choose two)

  1. NHRP shortens the configuration 01the hub router

  2. NHRP dynamically provides informatlon about the spoke routers to the hub

  3. NHRP disables multicast

D The hub muter uses NHRP to initiate the GRE tunnel with spokes E. The spoke routers act as the NHRP servers

Answer: A,B

Question No: 268 DRAG DROP – (Topic 2)

Drag and drop each IS-IS router type from the left onto the best matching OSPF router type on the right.

Select and Place:

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 269 – (Topic 2)

Which statement about the default QoS configuration on a.Cisco switch is true?

  1. AII traffic is sent through four egress queues

  2. Port trust is enabled

  3. The Port CoS value is 0

  4. The CoS value of each tagged packet is modified

Answer: C

Question No: 270 – (Topic 2)

Which feature can you implement to reduce global synchronization?

  1. marking

  2. NBAR

  3. WRED

  4. policing

Answer: C

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 251-260

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 251 – (Topic 2)

Which three message type are used for prefix delegation in DHCPv6?(Choose three)

  1. Solicit

  2. Renew

  3. Advertise

  4. DHCP Discover

  5. DHCPAck

  6. DHCP Offer

Answer: A,B,C

Question No: 252 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to exhibit R2 is configured as the R1 neighbor in area 51, but R2 fails to receive the configured summary route. Which action can you take to correct the problem?

  1. Replace the summary .address command with the area-range command

  2. Configure a summary address under R1interfate GigabitEthernet0/0

  3. Configure a summary address under R1 interface GigabREthernet1/0

  4. Configure the no discard-route command in the OSPF process of R1

  5. Gonfigure ip ospf n茅twork broadcast under the Loopback0 interface of R1

Answer: A

Question No: 253 – (Topic 2)

Refer to the exhibit .

Dumps4Cert 2017 PDF and VCE

Which action can you take to prevent loops and suboptimal routing on this network?

  1. Configure the rfc2328compatibility command under the Cisco IOS OSPF routing process only

  2. Configure the rfc2328compatibility command under the Cisco IOS OSPF NX-OS routing process only

  3. Configure the ref1583compatibility command under the Cisco NX-OS OSPF routing process only

  4. Configure the ref1583compatibility command under the Cisco IOS OSPF routing process only

  5. Configure the rfc2328compatibility command Cisco IOS and NX-OS OSPF routing processes

  6. Configure the rfc2328compatibility command under the Cisco IOS and NX-OS OSPF routing

Answer: C

Question No: 254 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. Which twostatementsabout the device configuration are 1rue?

(Choose two)

  1. The device has control-plane protection enabled 8.The device implicitly allows Telnet connections

  2. The GigabitEthernet0/1 interface of the device allows incoming SSH and SNMP connections

  3. The device has management-plane protection enabled

  4. The device allows SSH connections to its loopback interface

Answer: C,D

Question No: 255 – (Topic 2)

Which two statements about class maps are true? {Choose two)

  1. As many as eight DSCP values can be included in a match dscp statement.

  2. A policy map can be used to designate a protocol within a class map.

  3. The match class command can nest a class map with more than one match command is match-any.

Answer: A,C

Question No: 256 DRAG DROP – (Topic 2)

Drag and Drop to corresponding items

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 257 – (Topic 2)

For which r ason can two QSPF neighbor routers on the same LAN segment be stuck in the. Wvo-way state?

  1. The two routers have different MTUs on the interface.

  2. The two routers are configured with different priorities

  3. The intefface priority is set to zero on both routers.

  4. Both routers have th锚 same OSPF router 10.

Answer: C

Question No: 258 – (Topic 2)

Which two conditions must be before IS-IS Level1 routers will become adjacent?(Choose)

  1. The routers must share a common Autonomous 8ystem Number

  2. The routers must share a common process ID

  3. The routers must be in different areas

  4. The routers must share a common NETWORK SEGMENT

  5. The routers must be configured with the neighbor command

  6. The routers must be in same area

Answer: D,F

Question No: 259 DRAG DROP – (Topic 2)

Drag and drop the EIGRP query condition on the left to the corresponding action taken by the router on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 260 – (Topic 2)

Which two BGP attributes are optional, non-transitive attributes? (Choose two)

  1. cluster list

  2. local preference

  3. AS path

  4. MED

  5. weight

Answer: A,D

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE