[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 251-260

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 251 – (Topic 3)

In a rented office, workers are not assigned to specific cubes. The facility just began to use IEEE 802.1X authentication for the tenants. When workers have previously logged in to a PC, it works correctly, but when they move to another PC that has never been used before, they are unable to log in. Which redesign action will overcome this issue with minimal operational burden?

  1. Use machine authentication.

  2. Establish a quot;Bring Your Own Devicequot; portal.

  3. Disable and re-enable network authentication when a new worker logs in to a new machine.

  4. Enable MAC Authentication Bypass.

Answer: A

Question No: 252 – (Topic 3)

To improve the stability of the network and protect it from intrusions, you must design control plane security. Which two features should you enable as part of this design? (Choose two.)

  1. SNMP security

  2. uRPF

  3. IPsec

  4. IP receive ACL

  5. control plane policing

  6. role-based CLI access

Answer: D,E

Question No: 253 – (Topic 3)

You are deploying a nationwide intranet solution for a company with 4 data centers and 400 remote branches connected via a provider-based solution. As part of the network design, you must ensure efficient content distribution of training material to remote sites. Which two VPN technologies leverage replication in the network core and provide for efficient bandwidth optimization? (Choose two.)

  1. VPLS

  2. EoMPLS

  3. MPLS Layer 3 VPN

  4. GRE

  5. GET VPN

Answer: C,E

Question No: 254 DRAG DROP – (Topic 3)

You are designing a new data center network. Drag and drop new data center requirements on the left into the appropriate design principle on the right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 255 – (Topic 3)

Which two statements are correct about route redistribution? (Choose two.)

  1. iBGP is used within the AS to carry eBGP attributes that otherwise would be lost if eBGP was redistributed into IGP.

  2. The unequal cost multipath load-balancing characteristic is lost when redistributing OSPF into EIGRP.

  3. Mutual redistribution at multiple points can create a routing loop.

  4. Redistributing the entire BGP table from the Internet works well when using multiple OSPF areas.

  5. IS-IS does not support Layer 2 routes leaking into a Layer 1 domain.

Answer: A,C

Question No: 256 – (Topic 3)

To meet specific business requirements, QoS-marked traffic must be sent over a dedicated link. Which technology fulfills this requirement?

  1. MPLS

  2. Q-in-Q tunneling

  3. policy-based routing

  4. traffic policing

Answer: C

Question No: 257 – (Topic 3)

Which three methods allow storage access across an IP network? (Choose three.)

  1. FCIP

  2. Fiber Channel over GRE

  3. Fiber Channel over L2TPv3

  4. iSCSI

  5. NFS

Answer: A,D,E

Question No: 258 – (Topic 3)

Which mechanism can you use to improve network performance over PPPoE, IPsec, and GRE networks?

  1. Path MTU Discovery

  2. Simple Service Discovery Protocol

  3. ICMP Router Discovery Protocol

  4. Bidirectional Forwarding Detection

Answer: A

Question No: 259 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two options are two characteristics of the single-tier headend architecture for DMVPN designs? (Choose two.)

  1. The mGRE and crypto functions are on the same router.

  2. Each DMVPN cloud has two different headend routers for high availability purposes.

  3. It is used in dual-cloud topologies for spoke-to-spoke connectivity.

  4. It only supports hub-and-spoke connectivity.

  5. Spokes cannot be used as RP in multicast deployments.

Answer: A,C

Question No: 260 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

This new OSPF network has four areas, but the hub-and-spoke area experiences frequent flapping. You must fix this design failure. Which two mechanisms can you use to isolate the data center area from the hub-and-spoke area without losing IP connectivity? (Choose two.)

  1. Make the DC area totally stub.

  2. Make the DC area an NSSA.

  3. Convert the DC area to EIGRP protocol.

  4. Deploy a prefix summarization on router D.

  5. Use OSPF distribute-list filtering on router A.

Answer: A,D

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 241-250

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 241 – (Topic 3)

You have been tasked with designing a data center interconnect to provide business continuity. You want to encrypt the traffic over the DCI using IEEE 802.1AE MACsec to prevent the deployment of any firewall or IPS. Which two interconnect technologies support MACsec? (Choose two.)

  1. EoMPLS

  2. MPLS Layer 3 VPN

  3. DMVPN

  4. OTV

  5. VPLS

  6. GET VPN

Answer: A,E

Question No: 242 – (Topic 3)

Which three statements are correct for route filtering? (Choose three.)

  1. The OSPF router LSA can be filtered with route maps so they are not installed on the OSPF database.

  2. Route filtering can create suboptimal routing, thus increasing latency in the network.

  3. Inbound route filtering affects outbound traffic flow.

  4. By default, EIGRP filters topology information at every hop in the network.

  5. IS-IS filters reachability information from the Level 1 to Level 2 domain.

  6. By default, EIGRP filters the reachability information at every hop in the network.

Answer: B,C,D

Question No: 243 – (Topic 3)

Your company will attach to a new Gigabit Ethernet-based wide area network from the local service provider for remote connectivity. Each connection will have a 150 Mb/s committed information rate. For the design of this new service, which QoS mechanism should be used to ensure low packet loss toward the service provider network?

  1. shaping

  2. policing

  3. CBWFQ

  4. RED

Answer: A

Question No: 244 – (Topic 3)

You have been tasked with designing a data center interconnect as part of business continuity. You want to use FCoE over this DCI to support synchronous replication. Which two technologies allow for FCoE via lossless Ethernet or data center bridging? (Choose two.)

  1. EoMPLS

  2. DWDM

  3. Multichassis EtherChannel over Pseudowire

  4. OTV

  5. VPLS

  6. SONET/SDH

Answer: B,F

Question No: 245 – (Topic 3)

Which of the following design options meet the requirement to provide IPv6 interdomain multicast?

  1. MSDP

  2. PIM SSM

  3. Auto-RP

  4. PIM dense mode

Answer: B

Question No: 246 – (Topic 3)

Which multicast technology provides a large, many-to-many connectivity for a new application while minimizing load on the existing network infrastructure?

  1. Bidirectional PIM

  2. PIM Sparse Mode

  3. Any-source Multicast

  4. Source Specific Multicast

Answer: A

Question No: 247 – (Topic 3)

Which statement about the behavior of OSPF on a hub-and-spoke topology is true?

  1. Additional host routes are added to the routing table on a NBMA network type.

  2. The DR and BDR election occurs regardless of the underlying OSPF network type.

  3. The DR election is a challenge unless a point-to-point network type is used.

  4. Traffic does not need to traverse the hub to reach the spokes.

Answer: C

Question No: 248 – (Topic 3)

While designing a security solution, which three requirements would make you decide to deploy an IPS sensor in inline mode? (Choose three.)

  1. The solution should be resistant to sensor failure.

  2. The solution should allow for stream normalization.

  3. The solution should not impact jitter and latency for voice traffic.

  4. The solution should allow for signature-based pattern matching.

  5. The solution should allow denying packets inline.

Answer: B,D,E

Question No: 249 DRAG DROP – (Topic 3)

A small local business recently had an outage after an employee plugged a switch into the corporate network, which caused the traffic pattern in the network to change. You have been tasked to redesign the network so that this does not happen again. From the left side to the right side, drag the PVRST features that should be implemented to prevent the corresponding root cause. Not all sources will be used.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 250 DRAG DROP – (Topic 3)

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 231-240

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 231 – (Topic 3)

In a network design, there are three distribution layers and one data center. What are the two main reasons for using a core layer in this design? (Choose two.)

  1. The use of a core layer provides Layer 3 capabilities to the campus.

  2. The core layer reduces the number of ports that are needed in the distribution layers.

  3. The core layer is needed when there are two or more distribution layers that are to be connected.

  4. The core layer would fulfill core network functions such as DPI and security policies.

  5. The core layer is capable of faster forwarding than any other layer or module in the network.

Answer: B,C

Question No: 232 – (Topic 3)

Company Y is a mobile backhaul provider that uses microwave rings in their network. Which low-cost, simple technology do you recommend to Company Y to ensure the fastest convergence times in a ring topology?

  1. sub-second IGP hello and dead timers

  2. MPLS Traffic Engineering

  3. Remote Loop-Free Alternate

  4. IP Event Dampening

  5. hub and spoke with ECMP

Answer: C

Question No: 233 – (Topic 3)

What should be taken into consideration when designing IPsec networks using Authentication Header (AH)?

  1. NAT

  2. transform set

  3. crypto maps

  4. ISAKMP

Answer: A

Question No: 234 – (Topic 3)

What is the purpose of dynamically created tunnels using IPv6 multicast?

  1. multicast source registration to the RP

  2. bypass of the RPF check to the RP

  3. transport of all IPv6 multicast traffic to the RP

  4. first-hop router registration to the RP

Answer: D

Question No: 235 – (Topic 3)

You are redesigning an OSPF v2 network and must migrate some links. You are concerned that there are different subnet masks. Which two link types will still form an OSPF adjacency even if there are subnet mask mismatches? (Choose two.)

  1. virtual

  2. broadcast

  3. point-to-multipoint

  4. non-broadcast

  5. point-to-point

Answer: A,E

Question No: 236 – (Topic 3)

A Service Provider network designer is considering the use of the G.8032 Ethernet Ring Protection mechanism in order to provide resiliency in the network. Which three concepts will be supported with the implementation G.8032? (Choose three.)

  1. Ring Protection Link (RPL)

  2. Ring Automatic Protection Switching (R-APS)

  3. Multi-Router Automatic Protection Switching (MR-APS)

  4. Automatic Protection Switching (APS) Channel

Answer: A,B,D

Question No: 237 – (Topic 3)

Which two options are characteristics of firewall transparent mode operations in a firewall solution design? (Choose two.)

  1. The firewall acts like a router hop in the network.

  2. OSPF adjacencies can be established through the firewall.

  3. Changes in the existing IP addressing and subnets are required.

  4. Multicast traffic can traverse the firewall.

  5. The firewall can participate actively on spanning tree.

Answer: B,D

Question No: 238 – (Topic 3)

Which two headend router scalability factors should be considered when designing a DMVPN network solution that uses a hub-and-spoke topology? (Choose two.)

  1. the required aggregated packet per second

  2. the amount of bandwidth necessary to terminate all the remote tunnels

  3. the routing protocol chosen for the data plane routing

  4. the maximum number of tunnels supported by the headend router

  5. the CPU and memory of the headend router

Answer: A,D

Question No: 239 – (Topic 3)

Which Designated Intermediate System selection option is valid when deploying IS-IS in a broadcast medium that connects two networking devices as a point-to-point network type?

  1. There is no DIS selection on point-to-point network types.

  2. The router with the highest interface IP address is selected as the DIS.

  3. The router with the lowest interface priority address is selected as the DIS.

  4. The router with the highest loopback IP address is selected as the DIS.

  5. The router with the lowest interface MAC address is selected as the DIS.

Answer: A

Question No: 240 – (Topic 3)

Which VPN technology supports multivendor interoperability on a network design?

  1. VTI

  2. DMVPN

  3. Easy VPN

  4. IPsec VPN

Answer: D

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 221-230

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 221 – (Topic 3)

You are working on a network design for Customer A. This design should consider fast convergence features, and it was agreed that BFD should be used for faster link-transition detection. Which three options apply to the use of the echo function in BFD? (Choose three.)

  1. It can be used with asynchronous mode.

  2. BFD control packets are not required.

  3. It can be enabled individually in each direction.

  4. It has the advantage of testing the forwarding path on the remote system.

  5. The rate of periodic transmission of BFD control packets should be increased.

Answer: A,C,D

Question No: 222 – (Topic 3)

Which statement is correct about policy-based routing?

  1. It can create microloops during network reconvergence.

  2. It should be implemented at both ends of a GRE tunnel.

  3. It can limit the network scalability.

  4. It decreases failure detection time.

Answer: A

Question No: 223 – (Topic 3)

Which two options are considered risks or concerns when both the Internet and VPN service functions are on the same PE router? (Choose two.)

  1. Internet-based attacks can affect VPN customers.

  2. BGP cannot simultaneously run on the PE router that runs MPLS.

  3. MP-BGP prefixes increase routers#39; global routing tables, which affects network convergence.

  4. Failure on the PE router affects both VPN and Internet services.

  5. Customer performance can be affected by VPN traffic if Internet-based traffic is not prioritized on the PE.

Answer: A,D

Question No: 224 – (Topic 3)

You are designing an IEEE 802.1X solution for a customer, where the network supports a large number of IP phones and printers. You plan to configure MAC address bypass for the phones and printers. What is your primary design and security concern?

  1. the additional AAA traffic on the network

  2. the placement of the AAA server

  3. the potential of MAC address spoofing

  4. the scaling of the MAC address database

Answer: C

Question No: 225 – (Topic 3)

You are a network designer who must fine tune the convergence of an IS-IS network. The failure detection mechanism has been addressed with reliable loss-of-signal at the interface level. Which three other tools or techniques should be employed to achieve your requirements? (Choose three.)

  1. Use prefix prioritization techniques.

  2. Use BFD on point-to-point links.

  3. Speed up LSP generation.

  4. Disable LDP-IGP synchronization.

  5. Speed up the initial link state computation.

  6. Eliminate the time that the overload bit is advertised to neighbors.

Answer: A,C,E

Question No: 226 – (Topic 3)

When you design a network that uses IPsec, where can you reduce MTU to avoid network fragmentation?

  1. on both ends of the TCP connection

  2. on the side closest to the client

  3. on the side closest to the server

  4. in the WAN

Answer: A

Question No: 227 – (Topic 3)

Which option describes an advantage of UDLD?

  1. It makes the port go immediately into the forwarding state after being connected.

  2. It prevents switch loops by detecting one-way communications on the physical port.

  3. It prevents switched traffic from traversing suboptimal paths on the network.

  4. It prevents switch loops caused by uni-directional point-to-point link condition on Rapid PVST and MST.

  5. It does not generate a spanning-tree topology change upon connecting and disconnecting a station on a port.

  6. It allows small, unmanaged switches to be plugged into ports of access switches without the risk of switch loops.

Answer: B

Question No: 228 – (Topic 3)

You have been asked to design a high-density wireless network for a university campus. Which three principles would you apply in order to maximize the wireless network capacity? (Choose three.)

  1. Increase the number of SSIDs to load-balance the client traffic.

  2. Choose a high minimum data rate to reduce the duty cycle.

  3. Make use of the 5-GHz band to reduce the spectrum utilization on 2.4 GHz when dual- band clients are used.

  4. Enable 802.11ag channel bonding on both 2.4 GHz and 5 GHz to increase the maximum aggregated cell throughput.

  5. Use directional antennas to achieve better sector separation channel reuse.

  6. Implement a four-channel design on 2.4 GHz to increase the number of available channels.

Answer: B,C,E

Question No: 229 – (Topic 3)

On a large-scale DMVPN network design, what are two DMVPN characteristics? (Choose two.)

  1. DMVPN can interoperate with other vendors#39; equipment.

  2. DMVPN supports multicast replication at the hub.

  3. DMVPN supports non-IP protocols.

  4. DMVPN supports dynamic partial- or full-mesh tunnels.

Answer: B,D

Question No: 230 – (Topic 3)

You need to redesign your NMS system so that it can collect information without causing adverse effects in the network, such as high CPU utilization on network devices and network instability. Which two options will minimize the impact of the trusted NMS polling your network in this situation? (Choose two.)

  1. Implement SNMP community restrictions that are associated with an ACL.

  2. Unload unused MIBs from the network devices.

  3. Prevent polling of large tables through the use of SNMP OID restrictions.

  4. Disable unused OIDs and MIBs on the NMS systems.

Answer: C,D

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 211-220

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 211 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

RTR 1 uses RTR 2 as the primary WAN exit point. When a failure occurs in the link connected to RTR 2 LAN, it takes about 40 seconds for RTR 1 to use the backup path via RTR 3. Which two mechanisms can be used independently to improve the failure detection time to 1 second or less when RTR 1 failover to RTR3? (Choose two.)

  1. Configure EEM on RTR 2.

  2. Change OSPF throttling timer.

  3. Use BFD with OSPF between RTR 1 and RTR 2.

  4. Use BFD with OSPF between RTR 2 and RTR 3.

  5. Tune OSPF fast hello on all the routers.

Answer: C,E

Question No: 212 – (Topic 3)

Which three options are important functions of IPv6 first-hop security? (Choose three.)

  1. implements a broadcast-control mechanism

  2. limits IPv6 route advertisement in the network

  3. suppresses excessive multicast neighbor discovery

  4. prevents IPv6 packet fragmentation

  5. prevents rogue DHCP servers from assigning IPv6 addresses

Answer: B,C,E

Question No: 213 – (Topic 3)

What are three tools for ongoing monitoring and maintenance of a voice and video environment? (Choose three.)

  1. active monitoring via synthetic probes to measure loss, latency, and jitter

  2. passive monitoring via synthetic probes to measure loss, latency, and jitter

  3. flow-based analysis to measure bandwidth mix of applications and their flows

  4. flow-based analysis with PTP time-stamping to measure loss, latency, and jitter

  5. call management analysis to identify CAC failures and call quality issues

Answer: A,C,E

Question No: 214 – (Topic 3)

Which statement is correct about route reflector design?

  1. Route reflectors should be placed to find the best exit point from the AS.

  2. The EIGRP unequal cost, load-balancing characteristic facilitates route reflector placement.

  3. Route reflectors should not be placed on the data path.

  4. Route reflectors help find the closest exits from the AS.

Answer: C

Question No: 215 – (Topic 3)

You are redesigning an OSPF v2 network and must migrate some links. You are concerned that there are different subnet masks. Which link type will still form an OSPF adjacency even if there are subnet mask mismatches?

  1. broadcast

  2. point-to-multipoint

  3. non-broadcast

  4. point-to-point

Answer: D

Question No: 216 – (Topic 3)

To meet specific business requirements, QoS-marked traffic must be sent over a dedicated link. Which technology fulfills this requirement?

  1. MPLS

  2. Q-in-Q tunneling

  3. policy-based routing

  4. EIGRP with modified metrics

Answer: C

Question No: 217 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Assume that no multicast optimization is done on LAN switches A and B. Which two features can be used to optimize multicast traffic forwarding in this situation? (Choose two.)

  1. Enable IGMP snooping querier on both switches.

  2. Configure a static MAC entry for the multicast server.

  3. Disable IGMP snooping on both switches.

  4. Disable the IGMP query election process.

  5. Enable PIM snooping on both switches.

Answer: A,C

Question No: 218 – (Topic 3)

When designing IP addressing for route summarization, which consideration is true?

  1. Summarization can be applied regardless of the network topology if the IP addressing scheme is structured.

  2. IP address space assignments should be based on the divisions of the company.

  3. Suboptimal routing is commonly caused by the information that is hidden in the summary route.

  4. Summary metrics are constant, regardless of the instabilities of the summary components.

Answer: C

Question No: 219 – (Topic 3)

Which routing protocol supports unequal cost, multipath load balancing?

  1. RIPv2

  2. EIGRP

  3. OSPFv3

  4. IS-IS

Answer: B

Question No: 220 DRAG DROP – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Company ACME is adding a Cisco TelePresence system for real-time collaboration and wants to ensure the highest user experience. Drag and drop the necessary QoS mechanisms from the left to the right in any order. Not all options will be used.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 201-210

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 201 – (Topic 3)

Which two options are two advantages of summarizing networks at the aggregation layer rather than at the core? (Choose two.)

  1. It prevents the core from having unnecessary routes.

  2. It no longer needs a core layer.

  3. It prevents black hole routing.

  4. It avoids network-wide impact upon VLAN changes local to the aggregation devices.

Answer: A,D

Question No: 202 – (Topic 3)

A large service provider offers VoIP and Video services to business customers. Which three areas should the service provider monitor related to these services? (Choose three.)

  1. bandwidth utilization

  2. service response time

  3. packet loss

  4. jitter

  5. latency

  6. availability

Answer: C,D,E

Question No: 203 – (Topic 3)

Which multicast technology provides a large, many-to-many connectivity for a new application while minimizing load on the existing network infrastructure?

  1. Bidirectional PIM

  2. PIM Sparse Mode

  3. Any-source Multicast

  4. Source Specific Multicast

Answer: A

Question No: 204 – (Topic 3)

Acme Corporation wants to minimize the risk of users plugging unauthorized switches and hubs into the network. Which two features can be used on the LAN access ports to support this design requirement? (Choose two.)

  1. BPDU Guard

  2. PortFast

  3. Loop Guard

  4. Port Security

  5. UDLD

Answer: A,D

Question No: 205 – (Topic 3)

Dumps4Cert 2017 PDF and VCE

Which network topology is characterized by a link fate-sharing situation? A)

B)

Dumps4Cert 2017 PDF and VCE

C)

Dumps4Cert 2017 PDF and VCE

D)

Dumps4Cert 2017 PDF and VCE

  1. Exhibit A

  2. Exhibit B

  3. Exhibit C

  4. Exhibit D

Answer: B

Question No: 206 – (Topic 3)

In a routed access hierarchical campus design, the access-to-distribution Layer 2 uplink trunks are replaced with Layer 3 point-to-point routed links. Why is it recommended that VLANs are confined on a single access switch rather than span across multiple access switches?

  1. to allow for better convergence time

  2. to prevent the occurrence of Layer 2 loops

  3. to allow for fault isolation

  4. to prevent routing black holes

Answer: D

Question No: 207 – (Topic 3)

A large retail bank is designing a unified communications solution to be deployed to its 200 branches. Its current network traffic consists of a web-based portal, Internet browsing, and general file server access. Each branch has between 15 and 20 users. The current WAN is based on Layer 3 MPLS and the customer manages its own CE routers. The WAN circuit interface to the service provider is Gigabit Ethernet, although the MPLS service that is contracted from the service provider is 10 Mb/s. The design is to use a DSCP-based four- class QoS policy to manage traffic demands. From the options below, which two QoS design options that should be implemented on the customer side will meet the requirement? (Choose two.)

  1. Shape traffic to 10 Mb/s on the CE router.

  2. Police traffic to drop outbound traffic that exceeds 10 Mb/s.

  3. Classify DSCP value EF for call signaling and voice packets, and place traffic in a strict priority queue.

  4. Priority queue traffic to demand up to 80% of total bandwidth.

  5. Enable DSCP-based WRED on all AF classes.

Answer: A,E

Question No: 208 – (Topic 3)

Refer to the exhibit. Service Provider A has offered to help Service Provider B to provide local connectivity for a customer who has a business operation in North America and recently opened an office in Asia. The service to be offered for the customer is a Layer 3 MPLS VPN. Service Provider A and Service Provider B have never shared any business dealings or interconnected their networks. What is the most secure and easiest way for the two service providers to interconnect?

Dumps4Cert 2017 PDF and VCE

  1. carrier supporting carrier

  2. eBGP VPNv4 multihop between route reflectors

  3. back-to-back VRF

  4. VPNv4 peering between ASBRs

Answer: C

Question No: 209 – (Topic 3)

Which option is a BFD design consideration?

  1. BFD should not be used with RSVP-TE backup tunnels.

  2. BFD echo mode may reduce convergence time.

  3. BFD does not support sessions over MPLS LSPs.

  4. BFD is supported on indirectly connected peers.

Answer: B

Question No: 210 – (Topic 3)

What are two design characteristics of GETVPN? (Choose two.)

  1. It uses GDOI to distribute keys.

  2. It supports private addresses over public Internet.

  3. It requires multicast replication at the hub.

  4. It uses tunnel-less technology.

  5. It supports dynamic partial- or full-mesh tunnels.

Answer: A,D

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 191-200

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 191 – (Topic 2)

You are designing an Out of Band Cisco Network Admission Control, Layer 3 Real-IP Gateway deployment for a customer. Which VLAN must be trunked back to the Clean Access Server from the access switch?

  1. untrusted VLAN

  2. user VLAN

  3. management VLAN

  4. authentication VLAN

Answer: A

Question No: 192 – (Topic 2)

You have designed a network to support two offices connected by a T1. Your router serial interfaces will be configured with encapsulation PPP. What will happen to your EIGRP neighbors if there is an LCP failure once your network is implemented?

  1. Your neighbors will drop after the EIGRP timers expire.

  2. Your neighbors will stay up because the link has not gone down.

  3. Your neighbors will drop immediately.

  4. Your neighbors will drop and EIGRP will begin the query process.

Answer: D

Question No: 193 – (Topic 2)

Which two techniques are used in a network design to slow down the distribution of topology information caused by a rapidly flapping link? (Choose two.)

  1. Bidirectional Forwarding Detection

  2. IP event dampening

  3. link-state incremental SPF

  4. link-state partial SPF

  5. LSA throttling

  6. SPF throttling

Answer: B,E

Question No: 194 – (Topic 2)

An MPLS service provider is offering a standard EoMPLS-based VPLS service to Customer A, providing Layer 2 connectivity between a central site and approximately 100 remote sites. Customer A wants to use the VPLS network to carry its internal multicast video feeds, which are sourced at the central site and consist of 20 groups at 5 Mb/s each. Which service provider recommendation is the most scalable?

  1. EoMPLS-based VPLS already carries multicast traffic in a scalable manner.

  2. Replicate the multicast traffic on the P routers.

  3. Replace VPLS with a Layer 3 MVPN solution to carry the streams between sites.

  4. Use GRE tunnels to carry the streams between sites.

Answer: C

Question No: 195 – (Topic 2)

You are designing a large Frame Relay WAN for a customer. The routing protocol is OSPF. What is the effect on the routing table if the WAN interfaces are configured as point-to- multipoint?

  1. Only a route for the DR will be present in the routing table.

  2. Configuring point-to-multipoint has no effect on the routing table. The route that is configured with the area command will be seen in the routing table.

  3. Multipoint interfaces dynamically add the network of the connected interface.

  4. Multipoint interfaces dynamically add a /32 route for each neighbor in the WAN.

Answer: D

Question No: 196 – (Topic 2)

A Mobile Service Provider would like to design and deploy an Ethernet service which has similar physical link failover/failback characteristics on the active/backup links as the APS/MSP SONET properties. Which Layer 2 services should be considered to address this design feature?

  1. Port-Channel

  2. MLPPP

  3. Flex Link

  4. Ethernet Pseudowires

Answer: C

Question No: 197 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

When designing an MPLS-based LAN extension between DC-1 and DC-2, what are three advantages of deploying VSS? (Choose three.)

  1. Layers 2, 3, and 4 flow-based load balancing

  2. native VSS and MEC failover without using scripts

  3. sub-second failover

  4. required to configure VPLS

  5. failover time depends on Cisco IOS EEM and STP convergence

  6. limited VLAN-based VPLS traffic hashing

Answer: A,B,C

Question No: 198 – (Topic 2)

Your company requires two diverse multihop External Border Gateway Protocol peerings to a partner network. Which two methods would you use to improve lost peer detection? (Choose two.)

  1. Use Bidirectional Forwarding Detection for the peers.

  2. Use Selective Address Tracking and match the peers.

  3. Use subsecond keepalives for the peers.

  4. Use subsecond hold timers for the peers.

  5. Use Fast Peering Session Deactivation for the peers.

  6. Use subsecond minimum route advertisement Interval timers for the peers.

Answer: B,E

Question No: 199 – (Topic 2)

You are tasked to design a QoS policy for a service provider so they can include it in the design of their MPLS core network. If the design must support an MPLS network with six classes, and CEs will be managed by the service provider, which QoS policy should be recommended?

  1. map DSCP bits into the Exp field

  2. map IP precedence bits into the DSCP field

  3. map flow-label bits into the Exp field

  4. map IP CoS bits into the IP Precedence field

  5. map IP ToS bits into the Exp field

Answer: A

Question No: 200 – (Topic 2)

Which two OSPF design considerations should you implement to support the eventual growth of a network, so that CPU and memory are unaffected by the size and complexity of the link-state database in a large service provider network? (Choose two.)

  1. Turn on route dampening.

  2. Create network summaries.

  3. Turn on the Incremental SPF feature.

  4. Add more memory.

  5. Turn on packet pacing.

  6. Add redundancy between critical locations.

Answer: C,E

Topic 3, Volume C

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 181-190

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 181 – (Topic 2)

Your company experienced a number of network incidents that had a significant impact on business operations. Because a root cause cannot be identified, your CTO asks you to help the network management team implement the FCAPS framework. On which two areas would you provide guidance to the network management team? (Choose two.)

  1. change management

  2. accounting management

  3. service level management

  4. fault management

Answer: B,D

Question No: 182 – (Topic 2)

A company supports IPv4 and IPv6 addresses, and they need to be able to support flow- based translations for multiple IPv6 devices to a single IPv4 address. Which address family translation design solution should be recommended?

  1. stateful NAT-PT

  2. NAT-PT

  3. stateless NAT64

  4. stateful NAT64

Answer: D

Question No: 183 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

What limitations exist in this design, given that the access layer devices are expected to steadily increase by two devices per week for the next year?

  1. scalability

  2. serviceability

  3. redundancy

  4. resiliency

Answer: A

Question No: 184 – (Topic 2)

Your company plans to implement an Internet gateway router that is performing NAT. This same gateway will be terminating various IPsec tunnels to other remote sites. Which address type is appropriate for the ACL that will govern the sources of traffic entering the tunnel in the inside interface?

  1. inside local

  2. inside global

  3. outside local

  4. outside global

Answer: B

Question No: 185 – (Topic 2)

You are designing an IPv4 any source multicast redundancy solution. Which technology ensures the quickest RP convergence?

  1. Auto-RP

  2. Embedded RP

  3. bootstrap router

  4. MSDP anycast RP

Answer: D

Question No: 186 – (Topic 2)

You are the lead network designer hired by Service Provider XYZ to deploy CoS functionality on the core MPLS network (P routers). The goal of the network design is to provide a complete CoS solution to all customers that purchase services such as dedicated Internet access, MPLS L3VPN, and L2VPN (pseudowire). Service Provider XYZ has these design requirements:

->The network supports four service queues with equal treatment for delay, jitter, and packet loss.

->Queues are numbered 0-3, where 0 is the default queue.

->Three queues have one treatment.

->One queue has either one or two treatments.

If your design includes eight CoS queues on the Service Provider XYZ MPLS PE router ingress (CE facing) interface, how will customer traffic be classified as it enters the MLS P routers?

  1. The eight CoS queues in the MPLS P router are remapped to the eight CoS queues.

  2. Traffic is classified on the MPLS PE routers on core facing interface. The DSCP value is mapped into EXP field where multiple EXP settings (2 ) will be assigned to a single queue throughout the MPLS P routers.

  3. Discard the traffic from the eight CoS queues that does not match the four CoS queues

    of the MPLS P routers.

  4. The 8 CoS queues in the MPLS P router are remapped to four 4 flow-label queues.

Answer: B

Question No: 187 – (Topic 2)

Your company needs to baseline web traffic on a per-session basis for network application reporting. Which two mechanisms, when combined, fulfill the requirement? (Choose two.)

  1. Flexible Netflow

  2. Remote Monitoring

  3. Cisco IOS IP Service Level Agreement

  4. Class-Based Quality of Service Management Information Base

  5. Network-Based Application Recognition

Answer: A,E

Question No: 188 – (Topic 2)

The network administrator of a branch office network has decided to deploy Unicast RPF at the access layer. He insists that the design must guarantee that all the packets arriving on the router interfaces are assigned to the same interface subnet.

Which mode of Unicast RPF would you recommend as the lead network designer?

  1. uRPF strict mode

  2. uRPF loose mode

  3. uRPF VRF mode

  4. RPF feasible mode

Answer: A

Question No: 189 – (Topic 2)

Your firm has been awarded a contract to design a Criminal Justice Information Services

Version 5.0-compliant network utilizing advanced authentication policies. Which two methods could be utilized? (Choose two.)

  1. biometric

  2. PKI

  3. UKI

  4. password

Answer: A,B

Question No: 190 – (Topic 2)

What is a key role for the access layer in a hierarchical network design?

  1. The access layer provides a security, QoS, and policy trust boundary.

  2. The access layer provides an aggregation point for services and applications.

  3. The access layer serves as a distribution point for services and applications.

  4. The access layer can be used to aggregate remote users.

Answer: A

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 171-180

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 171 – (Topic 2)

A many-to-many enterprise messaging application is using multicast as a transport mechanism. As part of the network design for this application, which multicast address should be used, according to best practices outlined in RFC 2365?

A. 224.0.0.60

B. 232.192.0.60

C. 239.128.0.60

D. 239.193.0.60

Answer: D

Question No: 172 – (Topic 2)

A company wants to use an external appliance between its data center and WAN to optimize email and HTTP communications. The traffic flow must pass this appliance in both directions. The appliance is connected with only one interface to a Cisco IOS router and has a single IP address. Which two adjustments can you make to the network design so that the appliance is added into the traffic path? (Choose two.)

  1. Configure static routes to route the traffic to the appliance.

  2. Adjust the dynamic routing to route the traffic to the appliance.

  3. Configure NAT to force the traffic to the appliance.

  4. Configure a route map at the data center-side interface to forward the traffic to the appliance IP address.

  5. Configure a route map at the appliance-facing interface to forward the traffic to the appliance IP address.

  6. Configure a route map at the WAN-side interface to forward the traffic to the appliance IP address.

Answer: D,F

Question No: 173 – (Topic 2)

A junior engineer is implementing one of your optical designs and asks about CWDM (Coarse Wavelength Division Multiplexing). Which two features describe CWDM? (Choose two.)

  1. typically used over long distances, but requires optical amplification

  2. allows up to 32 optical carriers to be multiplexed onto a single fiber

  3. shares the same transmission window as DWDM

  4. uses the 850-nm band

  5. Passive CWDM devices require no electrical power.

Answer: C,E

Question No: 174 DRAG DROP – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 175 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

On this MPLS-based network ring, links have failed between router A and router E. These failures formed microloops while the network converged, when A forwarded traffic to B but B forwards it back to A. Which technology is the simplest solution to avoid microloops without enabling a new protocol in the network?

  1. TE Fast ReRoute

  2. IP Fast ReRoute

  3. Loop-Free Alternate

  4. Remote Loop-Free Alternate

Answer: D

Question No: 176 – (Topic 2)

Your customer asks you to assist with their traffic policy design. They want to guarantee a minimum amount of bandwidth to certain traffic classes. Which technique would you advise them to implement?

  1. Modular QoS CLI

  2. committed accessrRate

  3. policy-based routing

  4. traffic shaping

Answer: A

Question No: 177 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

You are planning the design of an encrypted WAN. IP packets will be transferred over encrypted GRE tunnels between routers B and C. The packet size is limited to a maximum of 1500 bytes inside the WAN between routers B and C. If endpoint 1 tries to send 1500- byte IP packets to endpoint 2, in what three ways will the network design handle the fragmentation in three different possible network configurations? (Choose three.)

  1. When router B fragments packets after the encryption, router C must reassemble these fragmented packets.

  2. When router B fragments packets before the encryption, router C must reassemble these fragmented packets.

  3. When router B fragments packets after the encryption, the endpoint 2 must reassemble these fragmented packets.

  4. When router B fragments packets before the encryption, endpoint 2 must reassemble these fragmented packets.

  5. When router A fragments packets, router C must reassemble these fragmented packets.

  6. When router A fragments packets, endpoint 2 must reassemble these fragmented packets.

Answer: A,D,F

Question No: 178 – (Topic 2)

You have been asked to design a wireless network solution that will implement context- aware services on an existing network that was initially deployed for data traffic only. Which two design principles would you follow to increase the location accuracy with the least possible impact on the current setup? (Choose two.)

  1. Use directional antennas to provide better cell separation.

  2. Add access points along the perimeter of the coverage area.

  3. Install additional APs in monitor mode where the cochannel interference would otherwise be affected.

  4. Increase the AP density to create an average interaccess point distance of less than 40 ft.

  5. Fine tune the access points radio configuration to have a higher average transmission power to achieve better coverage.

Answer: B,C

Question No: 179 – (Topic 2)

Which two aspects are considered when designing a dual hub, dual DMVPN cloud topology? (Choose two.)

  1. recommended for high availability

  2. requires all sites to have dual Internet connections

  3. spoke-to-spoke traffic will transit the hub unless spokes exchange dynamic routing directly

  4. hub sites must connect to both DMVPN clouds

  5. will only work with single-tier headend architecture

Answer: A,E

Question No: 180 – (Topic 2)

You are using iSCSI to transfer files between a 10 Gigabit Ethernet storage system and a 1 Gigabit Ethernet server. The performance is only approximately 700 Mb/s and output drops are occurring on the server switch port. Which action will improve performance in a cost- effective manner?

  1. Use a WRED random drop policy.

  2. Increase the queue to at least 1 GB.

  3. Enable the TCP Nagle algorithm on the receiver.

  4. Change the protocol to CIFS.

Answer: A

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 161-170

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 161 – (Topic 2)

What are two benefits of using BFD for failure detection in the design of a network? (Choose two.)

  1. BFD can provide failure detection in less than one second.

  2. BFD can be used as a generic and consistent failure detection mechanism for EIGRP, IS-IS, and OSPF.

  3. BFD eliminates router protocol hello notification.

  4. BFD can be used for all types of network interfaces.

  5. BFD is independent of the network protocol.

Answer: A,B

Question No: 162 – (Topic 2)

A Tier-3 Service Provider is evolving into a Tier-2 Service Provider due to the amount of

Enterprise business it is receiving. The network engineers are re-evaluating their IP/MPLS design considerations in order to support duplicate/overlapping IP addressing from their Enterprise customers within each Layer 3 VPN. Which of the following would need to be reviewed to ensure stability in their network?

  1. Assigning unique Route Target ID#39;s

  2. Assigning unique Route Distinguishers

  3. Assigning unique IP address space for the Enterprise NAT/Firewalls

  4. Assigning unique VRF ID#39;s to each Layer 3 VPN

Answer: B

Question No: 163 – (Topic 2)

A company would like to distribute a virtual machine (VM) hosting cluster between three data centers with the capability to move VMs between sites. The connectivity between data centers is IP only and the new design should use the existing WAN. Which Layer 2 tunneling technology do you recommend?

  1. VPLS

  2. L2TPv3

  3. OTV

  4. AToM

Answer: C

Question No: 164 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

In the DWDM network, a ring topology carries multiple services between two sites. Which option describes the employed protection design?

  1. Y-cable protection

  2. Splitter protection

  3. Client protection

  4. UDLD

  5. FEC protection

Answer: C

Question No: 165 – (Topic 2)

When adding an IPSec headend termination device to your network design, which two performance indicators are the most accurate to determine device scalability? (Choose two.)

  1. CPU capabilities

  2. bandwidth capabilities

  3. packets per second capabilities

  4. maximum tunnel termination capabilities

Answer: C,D

Question No: 166 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

You must ensure that both core A and core B devices have only the minimum information required for reaching the spoke routers yet maintain full reachability during network failures.

Which of the following design solutions accomplishes these requirements?

  1. Route summarization, with specific route leaking on hubs A and B

  2. Route summarization, with GRE tunnel on hubs A and B

  3. Implement PfR enhancements on hubs A and B.

  4. Implement ODR for hub-to-spoke routing.

Answer: B

Question No: 167 – (Topic 2)

An IBGP mesh design is being scoped, and in the discussions, one of the design engineers proposes the use of route reflectors. Which limitation is valid when using route reflectors in this design?

  1. The configuration complexity on the routers will be increased.

  2. Route reflectors will limit the total number of routes in the topology.

  3. Multipath information is difficult to propagate in a route reflector topology.

  4. Route reflectors will cause an opportunity to create routing loops.

Answer: C

Question No: 168 – (Topic 2)

A designer is working with a large bank to redesign their network. The designer wants to minimize complaints regarding slow application response times across the WAN. It is suspected that currently traffic is not being classified and marked correctly somewhere in the network. Which tool should the designer recommend to validate quality of service mappings and use?

  1. SNMP

  2. IPFIX

  3. IP SLA

  4. protocol analyzer

  5. NBAR

Answer: B

Question No: 169 – (Topic 2)

When network summaries are created for access networks in a network design, how does it change the behavior of the Shortest Path First (SPF) running in a backbone area?

  1. There would be fewer incremental SPFs.

  2. There would be fewer partial SPFs.

  3. There would be fewer full SPFs.

  4. There would be no change with the SPFs.

Answer: B

Question No: 170 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

You are designing a network using the Multiple Spanning Tree Protocol for loop avoidance. VLAN trunking is not allowed due to security requirements. Which option describes how you can design this Layer 2 network while using untagged interfaces between both switches?

  1. Assign VLAN 100 and VLAN 200 to the IST instance.

  2. Assign VLAN 100 and VLAN 200 to instance 1.

  3. Assign VLAN 100 to instance 1 and VLAN 200 to instance 2.

  4. Assign VLAN 100 to the IST instance and VLAN 200 to instance 1.

Answer: C

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE