[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 121-130

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-151.html

CCIE Data Center (v2.0)

Question No: 121

Which three statements about the virtual service domain on Cisco Nexus 1000v Switch are true? (Choose Three)

  1. Service virtual machine only snoops the data and is used for monitoring purpose.

  2. Any traffic coming into the VSD or going out of the VSD must go through the service virtual machine.

  3. A virtual service domain (VSD) allows you to classify and separate traffic for network service.

  4. vMotion is supported for the service virtual machine and should not be disabled.

  5. A VSD is the collection of interfaces that are guarded by the service virtual machine.

  6. The show virtualservice-domainname command displays the configuration for this VSD port profile.

Answer: B,C,E

Question No: 122

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which outcome of this configuration is true?

  1. It enables call home policies to take effect.

  2. Fabric interconnects can view neighbor switches.

  3. It enables the CIM XML service.

  4. It displays Cisco UCS Central on the UCSM portal page.

Answer: B

Question No: 123

Refer to the exhibit.

***Exhibit is Missing***

How many virtual adapters (vN|C and vHBA) can be added to this host?

A. 130

B. 128

C. 256

D. 258

Answer: C

Question No: 124

Which two statements about OTV are true?(Choose two)

  1. The authoritative edge device is the active forwarder for multicast and unknown unicast for all VLANs.

  2. The join interface must be a Layer 2 interface.

  3. no special license is required for OTV.

  4. OTV requires a separate VDC if SVIs for the extended VLANs are to be configured on the same switch.

  5. Only one join interface can be specified per overlay.

  6. OTV runs over a distance victor routing protocol. Answer: D,E

Question No: 125

You want to make 80 Gbps of bandwidth available to your RedHat servers. Which two

statements are true? (Choose two.)

  1. Install 2208 lOMs, VIC 1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  2. Install 2204 lOMs, VIC1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  3. Install 2204 lOMs, V1C1240 CNAs, and create four vNICs mapped to each fabric.

  4. Install 2204 IOMs, VIC 1280 CNAs, and create four vNICs mapped to each fabric.

  5. Install 2204 lOMs, VIC 1240 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

  6. Install 2208 IOMs, VIC 1280 CNAs, fabric extenders, and create eight vNICs mapped to each fabric.

Answer: C,F

Question No: 126

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

When specifying subnets under a bridge domain for given tenant, the user can specify the scope of a subnet. Which definition of the public subnet scope is true?

  1. It indicates that this subnet is advertised to the external router by the border leaf.

  2. It indicates that this subnet is advertised to public Internet and must be protected by a firewall.

  3. It indicates that it must be leaked to one or more private networks within ACI fabric.

  4. It indicates that this subnet is advertised to the border leaf in ACI fabric

Answer: A

Question No: 127

Which three options are valid sources for Cisco UCS monitor sessions? (Choose 3)

  1. VHBA

  2. uplink FC interface

  3. VLAN

  4. vNIC

  5. VSAN

  6. pin group

Answer: A,B,E

Question No: 128

Which descripting of how to enable the Flex Flash Controller auto-sync function on the B200M4 blade is true?

  1. Configure a focal disk policy for FlexFlash.

  2. Enable auto-sync in the servers gt; inventory gt; storage subtab.

  3. Configure a storage policy for FX3S.

  4. Configure a storage connection policy to use auto-sync.

Answer: B

Question No: 129

On Cisco Nexus 1000v Switch, you can allow the VSM and VEM to communicate over IP for control and packet traffic.Before you create a port profile for Layer 3 control, which two statements must be verified? (Choose two)

  1. Only one port profile can be configured with the capability Layer 3 control command.

  2. All VEMs belong to the same Layer 2 domain.

  3. The transport mode for the VSM domain should be configured as Layer 3.

  4. The port profile must be a trunk port profile.

  5. Different hosts should belong to the same VLANs for Layer 3 control. Answer: A,C

Question No: 130

Which option is the minimum number of vNICS required by the service profile to connect to all available

Vlans

  1. 6

  2. 7

  3. 3

  4. 1

Answer: C

100% Free Download!
Download Free Demo:400-151 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-151 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

Leave a Reply

Your email address will not be published. Required fields are marked *