[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-101 Dumps with VCE and PDF Download 311-320

Dumps4Cert 2017 Oct Cisco Official New Released 400-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/400-101.html

CCIE Routing and Switching (v5.1)

Question No: 311 – (Topic 2)

Exhibit:

Dumps4Cert 2017 PDF and VCE

  1. The PPP multilink protocol header is omitted on delay-sensitive packets.

  2. The maximum number of fragments is 1.

  3. Small real-time packets are multilink-encapsulated.

  4. A transmit queue is provided for smaller packets

Answer: A,D

Question No: 312 – (Topic 2)

Which command sets the maximum segment size for a TCP packet initiated from a router?

  1. ip tcp window-size

  2. ip tcp mss

  3. ip mtu

  4. ip tcp adjust-mss

Answer: B

Question No: 313 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which three statements about the R1 configuration are true? (Choose three)

  1. The virtual circuit identifier is 4006 and the virtual circuit is down.

  2. This circuit is using MPLS VC type 4.

  3. The local label for the circuit is 1611.

  4. The virtual circuit identifier is 1611 and the virtual circuit is down.

  5. The targeted LDP session to the remote peer is up.

  6. The local label for the circuit is 4006.

Answer: D,E,F

Question No: 314 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two options are effects of the given configuration? (Choose two)

  1. It enables Cisco Express Forwarding on interface FastEthernetO/0

  2. It sets the data export destination to 209.165.200.227 on UDP port 49152

  3. It enables NetFlow switching on interface FastEthernetO/0

  4. It configures the export process to include the BGP peer AS of the router gathering the data.

  5. It sets the data export destination to 209.165.200.227 on TCP port 49152.

Answer: B,C

Question No: 315 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are true? (Choose two)

  1. This router is 4-byte autonomous system aware.

  2. This router is not 4-byte autonomous system aware.

  3. The prefix 10.100.1.1/32 was learned through an autonomous system number with a length of 4 bytes, and this router is not 4-byte autonomous system aware.

  4. The prefix 10.100.1.1/32 was learned through an autonomous system number with a length of 4 bytes, and this router is 4-byte autonomous system aware.

  5. The prefix 10.100.1.1/32 was originated from a 4-byte autonomous system

Answer: B,C

Question No: 316 – (Topic 2)

Which command can you enter to disable logging for terminal lines?

  1. no logging trop

  2. no logging monitor

  3. no logging buffer

  4. no logging console

  5. no logging count

Answer: B

Question No: 317 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to exhibit. R1, R2, and R3 are in different statellite offices of the same organization. A multiast vido source is located behind R1. R3 frequently receives video streams interded for R2. These streams saturate the available bandwidth of R3. Which configuration change can alleviate the congestion on R3?

  1. Configure R3 to send an immediate-leave message when necessary 10 stop receiving unwanted traffic

  2. Configure IGMP snooping on R1 R 2 and R3

  3. Place a PIM filter 贸n the switches and interfaces that connect 10 R1R2 and R3

  4. Enable IGMP snooping On all switches that contect to R1 R2 and R3

  5. Place a PIM filter on the switch and interface that connect to R1 only

Answer: D

Question No: 318 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. Which two conclusions can you draw from this command and its output?(choose two)

  1. Rl0 has a missing label binding (or 192.168.40.171/32

  2. The MPLS ping failed

  3. 192.168.40.171/32 exists in the global routing table

  4. A valid LSP exists and it matches the corresponding MPLS FEC

  5. The MPLS ping was successful

  6. R10 has a valid lablel binding for 192.168.40.171/32

Answer: A,B

Question No: 319 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Refer to the exhibit. R1 and R2 have been configured as BGP neighbors, but their session is stuck in active. Which action can you take that will enable a session to be established?

  1. Enable synchronization on R1 R2

  2. Issue the neighbor 10.1.12 .2 activate command on R#39;1

  3. Configure 10.1.12.1 as the BGP router 10 on R1

  4. Configure a neighbor relation ship with the Loopback0 address of R1 on R2

Answer: D

Question No: 320 – (Topic 2)

Which option describes show a network administrator prevents possible routing loops for VLSM subnets that are missing from the routing table?

  1. Create a route for the subnet to the null interface and then redistribute the static route into the routing process.

  2. Create a loopback interface with the correct subnet and then redistribute the connected interface to the routing table

  3. Create a loopback interface with the correct subnet and the routing protocol automatically injects it into its routing process

  4. Create a route for the subnet to the null interface and the routing protocol automatically injects it into its routing process.

Answer: A

100% Free Download!
Download Free Demo:400-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 400-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

Leave a Reply

Your email address will not be published. Required fields are marked *