[Free] 2017(Oct) Dumps4cert Testinsides Cisco 352-001 Dumps with VCE and PDF Download 101-110

Dumps4Cert 2017 Oct Cisco Official New Released 352-001
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/352-001.html

CCDE鈩?Written Exam

Question No: 101 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which single design aspect should be configured on the ABRs to reduce the impact of WAN upgrades for spoke routers on the core of the network?

  1. route summarization

  2. stub area

  3. route filtering

  4. not-so-stubby area

Answer: A

Question No: 102 – (Topic 2)

A senior network designer suggests that you should improve network convergence times

by reducing BGP timers between your CE router and the PE router of the service provider. Which three factors should you to consider when you adjust the timer values? (Choose three.)

  1. access bandwidth

  2. service provider agreement to support tuned timers

  3. number of routes on the CE router

  4. number of VRFs on the PE router

  5. service provider scheduling of changes to the PE

Answer: A,B,C

Question No: 103 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

This Layer 2 ring has 10 VLANs with 1000 MAC addresses in each VLAN. Which protocol or mechanism provides the shortest traffic outage if the link marked with quot;Xquot; fails?

  1. PVRST

  2. REP

  3. MST

D. G.8031

E. BFD

Answer: B

Question No: 104 – (Topic 2)

As part of the security protocol for your network design, you have designated that option 82 is enabled for DHCP snooping. When option 82 is enabled, which information will be added to the DHCP request?

  1. switch MAC address and VLAN, module, and port

  2. remote ID and circuit ID

  3. switch IP address and VLAN, module, and port

  4. switch MAC address and switch IP address

Answer: B

Question No: 105 DRAG DROP – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 106 – (Topic 2)

How should multiple OSPF areas be designed when deployed on a classic three-layer (core/distribution/access) network hierarchy?

  1. The OSPF flooding domain boundary should be at the edge of the core layer.

  2. The OSPF flooding domain boundary should be within the distribution layer.

  3. OSPF should generally be deployed in a three-layer domain hierarchy to align with the physical three-layer hierarchy.

  4. OSPF flooding domain boundaries should be placed with route aggregation in mind.

Answer: D

Question No: 107 – (Topic 2)

What is a key benefit of a layered network design?

  1. cost savings

  2. increased security

  3. increased flexibility

  4. decreased broadcast

Answer: C

Question No: 108 – (Topic 2)

A company plans to establish a new network using Cisco Catalyst switches for its multicast applications. What is the disadvantage when two multicast applications are using the multicast IP addresses 234.17.4.5 and 234.145.4.5 inside the same network?

  1. Multicast packets from both applications are flooded to all Layer 2 ports in a segment where a multicast receiver is located.

  2. Multicast packets from both applications are flooded to ports where one multicast receiver from one application is located.

  3. Only one multicast stream is received at the port where the receivers from both applications are located.

  4. Both multicast senders will always receive the multicast packets from the other multicast application.

  5. The routers doing PIM-SM cannot distinguish between the two multicast applications.

Answer: B

Question No: 109 – (Topic 2)

You are designing a solution to eliminate the risk of high CPU utilization on a core network composed of CRS-1 devices. Which option would eliminate the risk of high CPU utilization across the network?

  1. Use Local Packet Transport Services (LPTS) to manage hardware SNMP flow rate.

  2. Use the in-band control plane policy feature to reduce the SNMP flow rate.

  3. Use the control plane policy feature and reduce SNMP flow rate.

  4. Use control-plane management-plane in-band and reduce the SNMP flow rate.

  5. Use the control-plane management-plane out-of-band feature to reduce the SNMP flow rate.

Answer: A

Question No: 110 – (Topic 2)

What are two functions of an NSSA in an OSPF network design? (Choose two.)

  1. It overcomes issues with suboptimal routing when there are multiple exit points from the area.

  2. It allows ASBRs to inject external routing information into the area.

  3. An ASBR advertises Type 7 LSAs into the area.

  4. An ABR advertises Type 7 LSAs into the area.

  5. It uses opaque LSAs.

Answer: B,C

100% Free Download!
Download Free Demo:352-001 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 352-001 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

Leave a Reply

Your email address will not be published. Required fields are marked *